Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
Hello,
I've purchased the nRF52840 Dongle: https://www.nordicsemi.com/Products/Development-hardware/nRF52840-Dongle . I've successfully flashed it with the version 4.0...
Hi：
I use nrf52832 to connect to the sensor module through uart. When the sensor device is turned off, I can repeat the pairing and unpairing of the Ble module through the...
Hello,
After reading many things, I would like someone to confirm or correct my understanding. I believe this will be great clarity for others as well.
The nrf52 requires...
Hello dear all. I am compiling a firmware to merge the timer function into the nrf52-ble-app-uart-c-multilink firmware. The timer function is copied from ble_app_uart__saadc_timer_driven__scan_mode...
Hi,
I am a new beginner when it comes to Thread and Matter. I am trying to run Matter on nrf52840. I flashed the door lock example, commissioned the device using BLE and...
I am using SEGGER Embedded Studio and an nRF52-SDK circuit board to run example ble_central\ble_app_hrs_c from nRF5_SDK_17.0.2. I have a peripheral that reports motions. The...
Hello Nordic, We are preparing for mass production with nRF9160. We have a script to flash, register the thing on AWS and write credentials on the modem using nrfjprog. We...
Using the debugger in SEGGER Embedded Studio and two nRF52-SDK circuit boards, I am stepping through code from the nRF5_SDK_17.0.2 examples.
Very often I end up in file...
Hello everybody,
I'm working on a Project with nrf52dk(nrf52832), and sdk 15.0.0 where I need to read the data from multiple sensors with twi/i2c and send the data via ble...
Hi,
is there a possibility to check in waht CE-level (ECL0- ECL2) the modem is operating on? I know that the ECL is decided by the network and not the UE. However it must...
Hi, I have a problem with simultaneously working Bluetooth LE with LTE. I've use nRF52832 as a Bluetooth controller with is connected to nRF9160 via Low Power UART HCI. When...
Hello I have a few issues which i can't handle. Platform: Visual Studio Code on Windows 10 Board: nrf52840 dk
In my project i need to create workspace which few different...
Dear N ordic S upport Team,
After I updated the nRF Connect SDK (1.5.1 to 1.6.1) and the Modem firmware (1.2.3 to 1.3.0) on my nrf9160 DK device (v1.0.0, SiP revision 2...
