Hello,
I am using Bluetooth device "NRF51822_xxAC_s110". My Bluetooth is not advertising when i dump the HEX file to the Bluetooth device which is generated by the Keil Version...
when creating a pairing with a peripheral, the application fails to exhange keys to allow for random private addressing so the peripheral cannot reconnect because the address...
Hi. i'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
I want to make sure that how to operate DFU.
Please check there is missing point or wrong point.
Step 1...
Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
Hi everyone
I have a question about zigbee. After reviewing the documentation, I realized that on the nrf52840 chip, you can use zigbee with a frequency of 2.4 GHz. But...
Hi, First of all, appriciate all your hard work on tech supporting, this is my first ask in this forum. I m currently using developing nrf52832 on Zephyr , working on the...
I'm trying to integrate mesh 4.0.0 into an existing project that uses sdk 16.0.0. I'm very close, but I'm getting an error when I try to run mesh_stack_start()
I traced...
HI everyone,
I am currently facing an issue when using nrfjprog to flash my nrf52832-based custom board using nrfjprog.
Here is the steps I followed:
- Creating application...
Hi,
I have recently been evaluating the nRF52840 for the research purpose. I came across a question related to this product that I could not figure it out myself.
I noticed...
Hi Nordic
Is there any sniffer can sniffing ANT traffic?
I just trying 52840DK and nrf-sniffer-3.0, and read user guide, it seems to sniffer BLE packets only.
Regards...
Hello Supports,
I downloaded the SUPL package, and extracted it to nrf/ext/lib/bin/supl/.
For enable it in gps example, I set CONFIG_SUPL_CLIENT_LIB to y in prj.conf...
I have borrowed a snippet from github nordic repository for doing a single Vdd voltage sampling. I lifted the code and installed it directly into my app. It appears to hang...
address = 0xe7 0xe7 0xe7(3bytes),
dataLength=0x01(8bit),
S1>>PID=0x01(2bit);NO_ACK=0x00(1bit);
How to calculate CRC, I need software calculation, not hardware processing...
Hi,
Greetings!
One of our product requirement is that we have to upload SIGmesh network data (lamp status, temperature etc) to cloud server
Here we have to use SIGmesh...
Hello,
will the Systick be sourced by the LFCK when in WFI/WFE low power mode (SYSTEM ON IDLE)? On nRF52 series the freeRTOS port uses the RTC as systick for its tickless...
Hi all,
I'm developing a board based on nRF52832.
I want to implement delay power on and power off through holding a single power button for about 3 seconds.
Regarding...
I am try to make twi communication and i got strange issue.
When i use twi scanner example with unconnected pins on my board , i am not see any requests
Great oddity that...
Hello,
I am working on nRF52382 IC. I am accessing GPIO also. But still i don't get the access of antenna. I have make the circuit as per the development board of nRF52...
Hi,
What is the practical maximum throughput of nRF proprietary protocol? The following table showing ESB and GAZEL has 1.3Mbps and 128kbps respectively.
https://www.nordicsemi...
