I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Hi,
I got strange behavior of the SPI4 nrfx driver on nRF5340 (using nRF SDK v2.6.1 non-secure build with BLE enabled on NET core). Namely, every time I try to receive bytes...
Hello DevZone,
Our team has been working on a customized firmware solution that has been flashed onto the nRF52840 Dongle to meet specific requirements.
Usually, DK is...
In pm_handler_secure_on_connection, I see that it only looks for BLE_GAP_EVT_CONNECTED events if PM_HANDLER_SEC_DELAY_MS is not in use. I also see the comment "In normal circumstances...
The power domains for the nRF70002 aren't very clearly documented in the product specifications, so we're not entirely clear on how we should be connecting the VBAT pin. ...
Hi Everyone,
We are developing a custom retail display solution based on the nRF52810 SoC .
Currently, we are facing an issue where BLE advertising does not start properly...
When my device receives data from the Xiaomi Zigbee switch, sometimes it reboots without any logs.
(Note: Normally, when there’s a bug, the device pushes logs to UART, but...
I was migrating from nrf52832 to nrf54L15, and found that,
ncs3.10 + NRF_SAADC_GAIN1_2 has opposite gain effect on nrf52832 & nrf54L15.
More specifically:
* on nrf52832...
I have started developing a new application based on NCS (previous products still using nRF5 SDK), using the nRF54L15 and I'm struggling with what should be basic tasks. Can...
Hi, I am developing a PCB based on the NRF52840-QIAA-R package.
The pads are very tightly packed, and I had to shrink the size of the middle ground pad to accomodate vias...
Due to the size limitations of the equipment, it is difficult to operate the low-frequency range of 700Mhz to 960Mhz for cellular antennas, and it is necessary to switch them...
hi
> AT+CGMR
mfw_nrf91x1_2.0.2
OK > AT+CFUN=1
OK > AT%XCONNSTAT=1
OK > AT%XCONNSTAT?
%XCONNSTAT: 0,0,0,0,0,0
OK > AT+CMEE=1
OK > AT%XSIM=1
OK > AT+CEREG...
Hi, I am designing a pcb using the nrf52805. In your reference design, the RF matching network specifies a 2.2 nH inductor in 0201 (0603 metric) package.
Unfortunately,...
Hello, We are working on a project based on the Thingy91x which uses the following SAW filter : SAFFB2G45MA0F0A. Unfortunately this part seems to be out of stock everywhere...
