hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Currently, I am only powering the NRF5340 chip to test its performance. I have opened a standard example project located in the directory: nrf\samples\bluetooth\peripheral_uart...
Hi, I’m currently working on a setup with three nodes:
Node A : collects data
Node B : acts as a relay, forwarding data
Node C : processes the data and then...
Dear Nordic Team,
I hope this email finds you well.
I am currently working on integrating group functionality with a Matter device (Node ID: 114, Endpoint ID: 1) using...
I was using an SPI serial nor flash device with NCS 2.8.0. I tried to get the flash into deep power down mode, but it doesn't seem to work well with NCS 2.8.0. So I upgraded...
Similar to ticket # 349557, we plan to operate nRF9151 in SLM mode and use both LTE and GNSS features. There is some interest in having GNSS (NMEA) data sent out on a dedicated...
Hi Team,
We have started our BLE development using nRF54L15 using SDK 3.1.0.
We have selected this MCU because it support all security features, we are going to start...
NFC certification and library.
https://docs.nordicsemi.com/bundle/ncs-latest/page/nrfxlib/nfc/README.html tells me, NFC is supported by nrf52 and 53.
e.g. libnfct2t_nrf52...
I am using nrf54l15 with NCS v3.1.0 with the following error when i connect it(i worked in NCS v2.9.1 successfully):
Controller unresponsive, command opcode 0x2035 timeout...
We as a company love the app (nRF Connect) and use it accross a lot of devices to recover stolen goods with BLE.
However, on all my Android devices (modern tablets and phones...
I am working with St7789v driver based RGB565 Display . I have chosen SPI21 configured at 8Mhz and if I send 15 bytes chunk of image bitmaps, I can see the image in the display...
Hello, I am testing the system off demo on the nRF54L15 DK using nRF Connect SDK v2.8.0 (Zephyr v3.7.99). I ran the sample exactly as provided in the SDK .
Observed log...
I am using the nRF7002DK with the nRF5340 SoC. By default the board runs at 1.8 V until I provide 3.3 V on VIOREF. Currently, I am using another board just to drive VIOREF...
Hello there,
we're using multiple pwm-channels of one module of the nRF54L15 for different purposes (multiple motors, h-bridge control; depending on the project).
When...
Can my Power Profiler 2 be faulty?
It does the following in both source meter and ampere meter mode. I start to measure and it shows some microamps current that's expected...
