I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
We are building a device where nRF9160 acts as a master that runs Zephyr OS (using NRF Connect SDK). Our device has a 2nd communication interface beside the nRF9160 modem...
Good afternoon.
We are engaged on a project that entails the simultaneous, independent development of two separate modules capable of interacting with the BLE stack. ...
Hello,
Im trying to debug my fw using Keil, its running in debug mode and I have RTT printouts, but once softreset occurs debugger doesnt halt it. Device reboots and starts...
fdsa
1.) From the nRF5 SDK I am using the example project for the Adafruit NFC Tag Reader.
2.) Using the project "as-is" I am able to get some basic information about...
Hello there,
I used both the oscilloscope and PPK to measure the current values. But both values are weird.
First, the PPK shows the current as large as 82mA. And...
Couldn't find an appropriate place to put this.
I use the Brave browser.
The ticketing system doesn't seem to work very well with it. Often I find that the options for...
I warry wander this fact.
I have migrated my project from SDK5 to ZEPHYR (nrf connect). Two devices - Central and Peripheral - Long range coded_phy.
I used next samples...
In certain situation when BLE device is disconnected during service discovery process sw can crash in bt_gatt_dm_char_by_uuid due to BUS FAULT (dereference of pointer showing...
I opened an issue on GitHub, but then I noticed that the README says to post issues on DevZone, so here I am.
I'm using the latest version of the Power Profiler app (3.1...
I'm looking at examples\ble_peripheral\ble_app_uart example and I have a couple of questions:
- You explicitly configure the UART inside the main so now once you have the...
Hi Nordic Team,
Since the OTS example is given only for nRF52840 DK and nRF52 DK which uses PCA10056 and PCA10040 respectively. How shall I use this example in my nRF52833...
Hello,
Project Description
in our project we have multiple nRF52DK and one nRF52840DK. We are using the SAADC on the nRF52DK. The SAADC is configured with 4 inputs in...
Sorry in advance for the length and possible irrelevance of some of what I have written here
So I am trying to figure out how the ble software works. I have the ble_app_blinky...
