I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
What is the difference between 'NRF_SDH_DISPATCH_MODEL_INTERRUPT', 'NRF_SDH_DISPATCH_MODEL_APPSH' and 'NRF_SDH_DISPATCH_MODEL_POLLING' in the 'NRF_SDH_DISPATCH_MODEL' related...
Dear All,
Currently I'm developing a BLE module that will be useful by its uart service and will use nrf51822. Nordic provided an example based on sdk 6.1 for low power...
Hello,
I want to read data from mesh network (from all the servers) to send it to a gateway. I saw in the documentation that Provisioner s can be a part of gateway devices...
Hi all,
I'm trying to enable Bluetooth 5 extended advertisement in nRF52840.
Currently, I'm using Nordic SDK v15.0.0 and S140 Softdevice v6.0.0.
In order to init the...
Dear Nordic Support Team,
I want to send the new PCB layout for manufacturer but I am not sure that
I can use any pairs of pin for DFU over serial or not.
I want to...
Hi all,
I have a question regarding the BLE mesh specification. When you are transmitting data using advertising frames, how does it check if the transmission medium is...
Hello everyone,
I am working on DFU bootloader application for android and iOS (using Qt C++).
For android everything works fine, but for iOS I have problems.
In order...
for the mass production what is the best solution in order to flash the nRF52?
for the mass production can I use DK PCA10040 ?
The DK PCA10040 can be used for dubbug on...
Hi I'm using Keil MDK 4.7 with nRF5 SDK V15, both of the 2 SDKs are installed at C:\, and the Keil4 Nordic License has been installed. When I tried to compile one of the example...
Hi all,
Is there any possibility to intimate any documentation errors(spell mistakes, content doubts, etc) to nordic documentation team?
Thanks,
Sridhar
Hi,
I have used examples\dfu\secure_bootloader\pca10056_ble application and successfully updated two applications(heart rate and health thermometer) over BLE. In order to...
Hello, i' trying to measure the power consumption of the nrf52840 PDK. So far i have been able to measure the current. How can i go about measuring the voltage and is it constant...
Hello, I recently received a Thingy:52 and was able to connect to PC using J-Link. After uploading Heart Rate Monitor program Thingy is no longer able to be added using iOS...
Hi,
I am facing difficulties porting Mesh examples to IAR.
I am getting the following error : #error "Your compiler is currently not supported." during compilation from...
