Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hi,
I am wanting to talk to this external 1Mbit RAM chip through an SPI interface: https://www.microchip.com/en-us/product/23lc1024 with the nRF5340 device. Preferably,...
Hi,
I am trying to use the clangd extension with nRF Connect SDK, as it does a much better job than intellisense. I added
set (CMAKE_EXPORT_COMPILE_COMMANDS ON )
...
Hi,
I have autoprovisioned and autoconfigured my nrf52840 board (provisioning and configuring are made inside the software and not through external app/provisioner).
In...
I have read info somewhere which said there is method to crack the protection just by setting UICR APPPROTECT register.
I want to know if Nordic has upgraded the protection...
Dear devzone, Can our nRF52840 detect 20 nanosecond voltage fluctuations using COMP? For example, if I set a lower threshold of 20mV and an upper threshold of 60mV, and the...
Hi，everyone:
We are developing a Nearby protocol combined with UWB, which needs to communicate with the Bluetooth of Apple phones and then use UWB to measure distance. We...
Hi nordic： What is the peak current of NRF9151? The relevant parameter cannot be found in the datasheet, while it is available for NRF9160.
Best Regards
JERMI.JIN
Hello,
I am working with the nRF7002 DK board and attempting to use the "Light Bulb Matter" example from Zephyr. I am encountering issues when trying to connect the board...
SDK 2.3.0
We have a custom board with a few GPIO connected to various interrupt sources (Button, sensor interrupts, power connection etc.)
We are experiencing here sleep...
I want to create automatic build using CI in bitbucket pipeline.
I would like to use image NordicPlayground / nrf-docker to compile the project. I saw the article Build...
Hi everyone
I have installed the nRF Connect for VS Code Extension Pack later tried to install toolchain the latest is v3.0.2 it successfully installed but im not getting...
I have a custom NRF9151 board with Windbond W25Q32JV flash, and some other peripherals connected. It also has GPS and LTE which I have tested and work. My UART console is...
Hi,
I want to use nPM1300EK、nPM PowerUP (official v2.1.1) profiling a chargeable battery, whose rated capacity、standard charging current is 2000mAh and 400mA respectively...
Hi,
I receive the following build error: "../zephyr-project-v4.1.0/modules/crypto/mbedtls/include/mbedtls/check_config.h:96:2: error: #error "Unsupported partial support...
Hi Team,
we are using two nRF5340 Audio DK kits to test LE Audio CIS example (unicast client & server).
kit1 nRF5340 Audio DK - act as gateway ( connected to PC/shared...
