I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
Hi all,
I need to generate two 1 MHz signals with opposite phases. However once I configure the decode mode as "Individual" I don't have output signals. In case of "Common...
Hi,
Where can I find the nRF9151 CE/RED RF test results for the purpose of CE delta certification of a new product based on nRF9151? (i.e. leveraging existing nRF9151 certification...
I am trying to configure the absolute time in my application, which at some point receives the time_t epoch value from an external source and should update it internally so...
Hi ! I have 5 different bootloaders for 5 pieces of hardware that I would like to cycle test OTA DFU with BLE. I have some questions
Why does nrfutil dfu ble require a...
Hi,
after having issues with my devkit flashing the main MCU, the interface MCU isn't being seen on USB anymore.
LED5 is blinking rapidly.
The board is a PCA10040...
I am creating a custom board with an W25Q128JVPIQTR external flash drive using SPI with a nrf5340. The pins are:
P0.08 - SD_CLK
P0.09 - SD_MOSI
P0.10 - SD_MISO ...
Regarding the operation of EJ2832AA1 (nRF52832), Please answer the following questions. nRF5 SDK ： v15.3.0 SoftDevice ： S132 v6.1.1
I am doing UART communication with another...
Hello, I am new here and I hope to not duplicate any other similar post (to be honest I have search a lot before writing). I am working with nrf52840DK, I have used blinky...
We're trying to set up MQTT messaging between our custom nRF9160 device and our private AWS VPC. When using the Serial Terminal in nRF Connect for Desktop to monitor the device...
I am reaching out to request assistance regarding a FOTA (Firmware Over-The-Air) operation using the HTTPS protocol for my new nRF7002-DK development kit. I have successfully...
Hi
I heard about that RSSI has no relationship with disconnection. However, based on my experiments, the connection will break every time I am close to -80dBm.
I am confused...
Does anyone know of a good starting point for Bosch BHI360 IMU integration into nrf5340 and Zephyr?
Did look at: https://community.bosch-sensortec.com/mems-sensors-forum...
Hi,nrf52832 entered in bootloader mode.as ld5 led is keep blinking on power reset and holding if boot/reset button.please help me to get board back to normal mode.thanks.
I had previously gotten working code to communicate with my SPI device on the nRF5340DK w/ NCS v2.5.0 that uses the HAL SPI library inside TF-M. I used NCS v2.5.0 (nrf\samples...
I observed another user having this same issue with resolution.
It appears the watchdog configuration has changed but I'm unable to track down the driver/overlay/etc that...
