I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
Hi
I have tried to reproduce the 2.7µA current consumption stated in the datasheet. This webinar shows that the UDP sample reaches 2.7µA on the nRF9160 evaluation kit. However...
Hello Nordic! My question probably a simple one but I'm a novice so there's it. I'm looking for a way to get a GPIO port state that was at the moment of GPIOTE event triggering...
Dear Nordic Support
We have an existing Project that uses the nRF9160 SoC and builds with toolchain v2.4.4 and SDK v2.4.4.
The project basically runs with the nRF9160...
Hello,
My DK stop working as programmer suddenly.
the VDD power is normal with 2.9V and the V5.
Try already to power on with reset button hold.
blinking is not Consitency...
Hi Support Team
We meet an issue like the screenshot below when I program nRF52840 chip via the SES.
The SES version is v5.42a.
The J-link we used to program is...
hi:
asset_tracker_v2\src\modules\led_module.c
I only found the file that calls the LEDs, I didn't find the specific initialization and control code? Can you tell me how...
Hello everyone, a pleasure and very grateful to be able to write in this forum.
I am trying to program a Nordic BLE device so that it does not appear in the pairing list...
Hello, I am developing a board using the nRF52840 QFN48 and powering it using a 3.7V single cell LiPo battery. Since the battery voltage is stepped down to 3.3V via an external...
Hi.
I would like con build nrf Connect OT COAP Client and Server on a zephyr 4.0.99 / toolchain: zephyr 0.17.0
I have downloaded nrf sdk 2.9.99
running:
west build...
Testing the RADIO TEXT example on 52811.
1. 52811 is not a supported target - so I must select all targets then the unsupported dts (nrf52840/nrf52811)
2. I add a Build...
Dear Team,
Is it possible to run BIS and PAwR concurrently while using PAST for synchronization? I am using the nRF52840 DK and NCS 2.8.
I managed to start two periodic...
I am working wih \nrf5_sdk_17.1.0_ddde560\examples\802_15_4\wireless_uart\secure\first\
And I want to add app timer to start a peroid works.
unfortunately， this timer...
Hi Q&A
At present, there is no routine found on the Internet about NRF52832 Bluetooth sending more than 6 characters(NKRO)
I used nRF5_SDK_17.1.0， The following is the...
