I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hello,
I am encountering difficulties connecting to and recovering my nRF52840 board with J-Link on macOS, both via nRF Connect and using nrfjprog in the terminal. Below...
Hello,
We are using the nRF52840 dongle (PCA10059) with the CLI agent software as a Zigbee network coordinator, and the Digi's XBEE S2C as a Router.
We are using XCTU...
Hi Team,
I have nRF5340 DK board and I want to test the Bluetooth Periodic Advertising with Response and Bluetooth Periodic Advertising with Responses Synchronization...
Hi,
I am trying to create a new custom service in nRF Connect for desktop and play around with its characteristic properties.
I Use an nRF52840 DK as peripheral and my...
Hi,
Its maybe a stupid question but is there a easy way to operate the DK with 3V VDD and IO Voltage? The 9160 DK had a simple switch for this. The default for the 9151...
Hi everybody I'm using nRF Connect SDK 2.6.1. Before I could seen Partitions section in Memory Report tool, but now it's disappeared. I also checked it by ninja command: ...
Hello,
I have a few questions: 1. How to add a prj.conf or an overlay file to enable peripherals to use an external high-frequency crystal oscillator as the clock source...
We have developed a firmware application using the OpenThread library for the nRF52840, utilizing the Nordic Development Kit and Segger Embedded Studio for ARM (version 5...
Dear nordic support team,
after having migrated my project to SDK release 2.8.0, the following message appears in the logs:
<dbg> bt_sdc_hci_driver: configure_memory_usage...
"I'm working with nRF Connect SDK v2.2.0 for nrf52840 and I'm trying to implement file transfer functionality using mcumgr over UART in Application. I've successfully configured...
Hi , I flash periodic_sync_conn sample to A and B development boards, and periodic_adv_conn sample to C development board. Only A and C development boards work normally, but...
Hello. We are developing custom boards with the configuration of nrf5340 + nrf7002.
In the previous sta example, a build error occurs when the "Board Target" in "build configuration...
I have customed my own nrf54L15 board and it would run on button battery. I managed to measure the battery level through ADC, but I don't know how to use ADC with nrf54L15...
I've been working for months to try and figure out exactly how to get my application to bond the way I want it to.
I'm using nrf connect sdk 2.4.2 on an nrf52832. I used...
