Hello!
I am working with the example mpu interface projects located at the following repo:
github.com/.../nrf5-mpu-examples
After converting the Keil projects to...
I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
Hi,
Recently, I faced very weird problem which stops working MCU when MCU enters low-power mode.
Not all PCBA I made have the same problem but quite many PCBA shows the...
hello, this is my first time to start the PPK, I have a 52840 DK (BMD-340-EVAL) and PPK, when I use nRF connect to connect the PPK(PPK is over the 52840 DK) , it shows Failed...
Hi Nordic Community
I'm busy developing a board around the nRF9160. Do you have a KiCad library/component for the SOC, do I need to make one myself, and if you do have one...
I'm trying to use the SPIM driver on nRF52832. The setup is:
Chip: nRF52832
SDK: 15
Softdevice: s132 v6
Toolchain: GCC
For some reason the call to nrfx_spim_xfer...
Hello,
I'm trying to configure the max -min of interval params and supervision timeout to obtain timeout of android = 1s.
i configure all parameters to run function...
Hi,
I am using the nrf-52840 DK.
I modified the pwm_library to output 125khz frequency.
app_pwm_config_t pwm1_cfg = APP_PWM_DEFAULT_CONFIG_2CH(125000L, NRF_GPIO_PIN_MAP...
Hi ,
The nrf connect for desktop programming works good on my desktop before.
The tool shows error message "cannot find module 'usb' " today.
I ever try re-install the...
I am working on integrated peripheral and central device used for indoor positioning. The device has two modes, at boot it is a peripheral for some duration of time then it...
Hello, we have been using a nRF51822 8-pin RF module for a while now for various products, the pinout is as follows: power, P0.00, P0.01, P0.09, P0.11, SWDIO, SWDCLK, ground...
Hi I try to implement DFU to our application using Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0 When I use the DFU-Example everything works fine. I then implemented the DFU-code from...
Hi there, I have a custom board with nRF52840 and i am transferring fairly large amounts of data via uarte. I am also using my own driver. For some reason the attached device...
Hi,
I am Using NRF52840-DK Board. We are trying to transmit multiple data using NRFx_SPIM Example. for single reg read it is working fine.
please check below code is...
Hi,
I have certain doubts regarding simple message model .
1. Why simple_message_client_init or simple_message_server_init is never used? Don't we need this function to...
Hello,
I try to control led light of the thingy52 throw a MIT app inventor application.
I use the UUID : ef680300-9b35-4933-9b10-52ffa9740042
and thr characterixtic...