here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
To preface:
nRF Connect SDK 2.9.0
nRF9151 DK
Windows 11 PC
Hello,
I just stumbled upon a potential issue after trying to figure out why I couldn't use 'softreset...
Hello, I'm having problems trying to make the MODBUS RTU Client code work on my board.
I'm devoloping with nrf Connect SDK v2.1.0, using Visual Studio Code.
The board...
I build the NCS 2.9.1 connectivity bridge with
west build -b thingy91x/nrf5340/cpuapp
when I try to flash that with jlink, I get
west flash -- west flash: rebuilding...
Hi I'm trying to get more insight about nRF7002 power supply requirements. My last question didn't get a follow up so I guess a block diagram of the internal power arch was...
What would happen if a battery were connected in reverse to the nPM1100? Would it cause damage to the IC, trigger any protection mechanisms, or result in abnormal behavior...
When Developing with nRF5 SDK, follow the Developing for the nRF52805 with nRF5 SDK - Getting Started - nRF5 SDK guides - Nordic DevZone 。
The Peripheral UART Example runs...
Hi Nordic,
I have a general question about kernel threads in the mesh stack. From memory, Bluetooth has its own thread in the stack I think. At some point in the stack the...
Hi,
As title, please help to share the required information for nRF52085 pre-design evaluation, thank you.
1. Reference schematic & layout file & guidance.
2. Design...
I've installed Visual Studio Code and nrfutil and nRF Connect and J-Link and managed to compile Blinky and flash the Thingy:91 X using the terminal:
./nrfutil device program...
Dear all,
I’m working on a project using the nRF9151-DK and need to implement frequent data transmission via LTE. My setup includes multiple I2C sensors, and I want to send...
Hi everyone,
I am getting this build error while I am trying to call a function from gpio.h in my custom code
Looking at my includes I see this
This is a really...
Hello,
I'm just starting with the Power Profile Kit 2. I've read all available documentation but I didn't find any information about the switch SW1 called 'POWER'. There...
Hi,
I'm using an nRF52810 on a custom board and I'm using softdevice s112_nrf52_7.2.0_softdevice.hex.
I want to write some information (just 4 bytes) to flash memory,...
