Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Problem:
Reset reason logic works correctly when programming via SWD
After DFU programming, reset reasons are detected incorrectly
Even after unplugging/reconnecting...
Hello all, I've just bought nRF9151 DK and went with Quick Start. I loaded nRF Cloud multi-service sample. Sample runs and connect to network. Sometimes it sends data (location...
I am following the Cellular IoT Fundamentals course and trying to get my nRF9151-DK set up as a device in the nRF cloud. ( https://academy.nordicsemi.com/courses/cellular...
Hi
I have two nRF54L15 DK boards (PCA10156).
Both are behaving the same way right now.
.......................................
ONE: Using nRFConnect in VSCode...
Hi,
I am currently developing a heart rate strap using SDK 17.1.0 and the S312 SoftDevice with the nRF52805. I have noticed an issue: when I connect the heart rate strap...
Hi
I'm using the periodic_adv_conn example from SDK 3.0.0. In the request_cb function, the bt_le_per_adv_set_subevent_data function is used to load data for future subevents...
Hi,
I want to use the die temperature sensor in the nRF54L chipset and am wondering why the definition have changed slightly compared to previous chipsets. In the SoC device...
How precise do the trace antenna dimensions have to be? Given that the datasheet for the nRF54L15 only has a reference layout up to and including the matching network, but...
Hi Nordic:
We currently need to provide the RoHS and MSDS test certificates for our product's NRF52820QDAA-R. I checked the certificates on Nordic's official website, but...
While testing, I encountered the following error after flashing the modem firmware and running the DECT example:
<err> nrf_modem: Modem has crashed, reason 0xfff, PC: 0x0...
Greetings,
I want to change Device name on Advertising. Is that possible? I am using nrfSDk52832, I want when some state of Switch is change, to change advertising name...
I am new to this device, so please bear with me during the inevitable simple misunderstandings! I am scanning for bluetooth devices and getting sensible numbers of devices...
Hi, I have a custom board with an ISP1807 onboard. We'd like to optimize the production process, especially the programming process. We currently use the nrf52840 dk board...
I have a small demo, based on the hello world example, where I have also enabled gpio_keys. I can run this on the nRF52-DK, nRF54-DK but when I come to run it on my custom...
I have seen a few posts including:
Change advertised name (Bluetooth) - Nordic Q&A - Nordic DevZone - Nordic DevZone (nordicsemi.com)
NCS bt_set_name() - Nordic Q&A...
