I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hello all,
I would like to have some help regarding the usage of CoAP protocol. Is there any sample project that supports SDK 17.02 that I can start from?
I am using...
Hi DevZone,
Here's my setup:
Using NRF5 SDK 15.2.0, custom board based on NRF52840
Battery powered device with 3.6V battery.
Supply voltage stepped down to 1.8V...
Good day
Due to I am very new with NRF chips and I did not find direct answer on forum I require some clarification on that moment...
The task is to detect input pulse...
Would like to capture the HCI flow through rpmsg (Rx and TX) using the btmon tool between application and network core. could not successfully do it.
Procedure:
1. Build...
As mentioned in the DK board User guide nRF52840_DK board is preprogrammed, so, till now we didn't flash the DK board.
I tested the nRF52840_DK board using J2 USB connector...
Hello, with the new version of the nrf5340 version D in the NET CPU RTC0 stops to work and the RTC0 IRQ is not called
now for example the counter is stopped at 87 and the...
Hi,
My problem is that I can't sniff any advertising packet using Wireshark.
I have well followed the detailed procedure https://infocenter.nordicsemi.com/index.jsp...
BLE app uart code write to the BMD 350 device. BLE is disconnected.
If any reasons?
How to configure the TX and RX pins ? when i change the pins, fatal error will come...
Is clearing the NRF_UART_EVENT_RXDRDY really sufficient before exiting the IRQ handler? Since Cortex M4 is used, there's no need to clear the pending register (to avoid the...
Hi, Could you pls check, is it ok if these logs happened?
No firmware defined for selected device Please make sure the device has been programmed with a supported firmware...
Hello
I would like to modify the example "ble_thread_dyn_mtd_coap_cli_nfc" to use Just Works pairing instead of OOB with NFC.
To do this, I modified this in sdk_config...
Hi,
I worked few years ago on a project with the configuration below :
nRF Mesh SDK V1.0.1
nRF52832
I used the light switch example where the client and the provisioner...
Hi, I have built a project upon the aws_iot-example. There are three shadow-topics that the device may publish to (/update, /get and /delete). To me it seems there is no possibility...
