I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
I have a development board and load the client central BLE blinky to it, then the peripheral BLE blinky to my custom board and power up and the central development board stays...
I was wondering if it is possible to do HTTP requests with the nRF9160 just by using AT commands? Since this is usually possible with such kind of modules.
The reason is...
Hello everyone,
I've got a three type of devices: 1 Central device, 2 Peripherial devices, and mulitple beacons. Central is connected with two peripherial devices with...
Hi Devzone,
We are using the nRF52 DK in a prototype which is under stress, and we noticed that any bending of the board breaks the BLE connection.
To easily replicate...
Hello,
I am currently writing a script whose purpose is to automatically provision and configure devices.
My question is related to the devkey_handle and address_handle...
With SDK 14.2.0 and S332 softdevice, I'm using UART to control ESP8266 WiFi module with AT commands and I'd like to replace app_uart (+FIFO) with nrf_serial , in order to...
Hi,
I am setting OOB with sd_ble_gap_auth_key_reply() method { 0x11, 0x11, etc 16 bytes }, but when trying to connect with desktop nRF Connect there is an error 132 inside...
Hi,
I am getting errors when attempting to include the nvs library to save data to flash storage on the nRF9160 DK. My CMakeLists.txt:
I get the same errors with or...
Hi,
We tried to use a smartSIM from Sierra Wireless with the nrf9160DK without success.
The nrf91 can connect to the LTE network after a few minutes (LED4 steady). However...
Hi,
I did have a working development board. I was working to disable serial and disable as much as possible to get the power usage down. It seemed to be working (although...
I tried this using the ram_retention example from the SDK (nRF5_SDK_15.3.0). The example (Ram Retention) still seems to work if the lines concerning NRF_POWER->RAMON and NRF_POWER...
Hi,
our appliction need to using I2S worked at 96kHz sampling, and i find two parameters , MCK and the CONFIG.RATIO,but when i use this formulation:
LRCK = MCK /CONFIG...
Hello,
I think about connecting two central devices (nRF's 52840) using one common antenna. One device will be only RX and will scan for a advertisements, second will manage...
Hi, I am from China. My company made a BLE module with chip nRF52810. Recently , I coded a program for it by SDK12, based on ble_app_uart example. I modified the corresponding...