[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
Hi,
SDK 3.0.2, nrf9160 (actinius icarus som), custom board, based on modules example. LTE-M with PSM.
Floor current is too high, at around 500 uA. There is a known issue...
Hi,
I am looking to create use a pm_static.yml to create a partition table for MCUBoot, which have the internal flash as the primary boot partition and the external SPI...
I get this error after creating a custom board
C:/ncs/v3.1.0/nrf/subsys/mpsl/init/mpsl_init.c: In function 'm_config_clock_source_get': C:/ncs/v3.1.0/nrf/subsys/mpsl/init...
I'm attempting to put together an application using the baremetal version of NCS just released... I need these to run DFU over BLE so we can update in the field.
I created...
Hello,
I am experiencing a recurring issue when programming multiple nRF52840 boards using the nRF Programmer.
Problem description: When programming the first board...
Hello, I have a pin that controls the power flow to the sensors on my board. it is active low, when it gets a raw value of 0, it allows the power flow to the sensors. I have...
I have just upgraded my project to NCS 3.1.0 and I'm now getting this error
BOOT_SWAP_USING_MOVE (defined at C:/ncs/v3.1.0/bootloader/mcuboot/boot/zephyr/Kconfig:575) set...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hi, I am working on storing data in the Trusted Zone using the PSA APIs.
I tried the Protected Storage (PS) example. When I store data using psa_ps_set() and then read the...
I am updating our automation software for programming Thingy 91 and trying to communicate to ModemShellRtt using python. In my test program attached, I would only like to...
Hi all,
I am working on a project to remotely control iPhone cameras via Bluetooth. I can already emulate the shutter button using the Volume Up command (0xE9). However...
Is it necessary to Update nRF SDk and Toolchain each time a new version comes, can't I use one version constantly. As with each update some libraries are getting removed or...
Our setup:
Board: nRF5340 DK
SDK: NCS v2.6.2
Microphone: MMICT5837-00-012
Interface: PDM
During mono audio capture over PDM, we observed a current draw of about...
Hello,
we are developing few products based on the nRF52833 and we found something interesting in the nrf52833 dts file ( https://github.com/nrfconnect/sdk-zephyr/blob...
