Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
Hi,
I'm developing a firmware based on Zigbee CLI sample. And I enabled DFU of app core and net core via serial with serial recovery mode.
Using SDK v2.4.2 and nRF5340...
Hi,
I am trying to integrate i2c code in peripheral_uart example from ncs 2.8.0.
I am following the steps as instructed in this exercise:
Exercise 1 - Nordic Developer...
I have nRF Connect for VS Code v2024.11.75 and am using SDK 2.6.1. In Lesson 3, Exercise 1 of the nRF Connect SDK Intermediate course in step 8 the instructions show to open...
I am a long time user of Doxygen and I am familiar with its format. I have been using Doxygen manually in my nRF9160 code and it is working fine. I am using DoxyWizard to...
Hi I am working on a project where I am trying to implement Bi-directional communication between 2 nrf modules connected to stm32f411ve dev boards. I am facing issue with...
nrf52840 with the official usb hid_generic routine transplant, the computer's 2.0 port hot swap probability is very small power-off restart, other ports are not tested out...
1. dts config file, I2C_SDA is configed GPIO P0.09/NFC1 , I2C_SCL is configed GPIO P0.10/NFC1, months ago, I'm using the old SDK, I also found that these pins configed as...
Hi Nordic team,
We need assistance in determining the appropriate GPS mode for our application: A-GPS or P-GPS? Though we believe A-GPS is more suitable for the use-case...
Hello,
My coleagues and I have been developing our application on the nRF5340 Audio DK for a while now and everything is working fine. Now we are at a stage where we want...
I am working on a custom development board with nRF5340 MCU. I have used two mics and integrated the LC3 codec library. I have assigned the following spaces in the prj.conf...
Hello,
I'm using a nRF5340 DK and ncs version 2.3.0.
What i try is, to use calls like
sdc_hci_cmd_vs_zephyr_read_chip_temp() that is available in header file sdc_hci_vs...
How can we retrieve all network devices RSSI/LQI value? Is there option to subscribe value for LQI ? We just want to showcase LQI/RSSI on server so user be aware if device...
Hi,
How can I retrieve the complete list of supported input and output clusters for all endpoints on a Zigbee end device? I'm currently able to access the On/Off cluster...
Hello,
I'm trying to use several USB CDC ACM instances with USB_DEVICE_STACK_NEXT. (nRF Connect SDK 2.8.0)
Is there a way to set the VID?
And is there a way to set different...
hello, when trying to program my 9160 board, I get this: I already tried the recover command but that yielded the same results. thanks in advance -shlomo
