We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello
I am using sdk v17 and nrf52dk and implementing sensor encryption(AES CTR mode) and simple nus service. After reading the sensor to saadc, I want to encrypt and transmit...
Thanks in advanced. I'm using nrf52832 with nRF5_SDK_17.0.2. I try to measure adc time consuming as below:
I find when timer sample rate is 500ms, then adc time consuming...
Hi:
I am doing a project which will use both PDM interface and bluetooth transreceiver, PDM interface is used to receive audio data from a MEMS microphone and Bluetooth...
We have a design that uses a simple custom board with an NRF52832 chip, button, accelerometer and onboard battery. For many phones, the operation is quite stable - we connect...
Hello all:
I've developed an nRF52810 application based on the UART example, but when I include buttonless DFU support to my application, it doesn't work. I'm using SDK...
Hi,
now I had achived the function to communication using the esb in nrf52832 that one to one,but I need to achive multi tx device to one.
if there not doc for me to achive...
Hi
Strange that there is no example for such popular code which will allow changing the iBeacon setting parameters (like: name, power, interval etc). with a smartphone application...
Hi everyone,
I'm trying since a few days to connect the Thingy 91 to the network with any result at all.
This is my configuration:
Modem firmware: V 1.3.0
Application...
Hi,
Am trying to store the data fetched through ble scanning to the flash memory of the nrf52840 DK. So I have been making use fo the flash_storage example in the SDK/examples...
Hello,
Our Peripheral server application regularly uses a stream of notifications to transmit data to a Central client. We have a rare error in which sd_ble_gatts_hvx returns...
app time loop update 200 byte data use fds by 10s ,then after many time error happened, update_user_flash is update API, write_drop_record IS loop write API in app time, ...
When running in High Voltage mode, it specifies a maximum of 7mA of external power draw on the Vdd output. It also specifies the voltage accuracy of -10%/+5%. This is a very...
HI devzone
Everytime after i executed "nrfjprog -f nrf53 --recover" on nrf5340 DK
i see it write around 4KB data into the flash. do you know what is the meaning for this...
When writing to flash it is MUCH easier to perform the write if SoftDevice is disabled. If it is not, one has to wait for an event to continue writing. ON the Nordic platforms...
Hi,
Is it possible to set the USB serial number for the nrf52833 and nrf52820 MCU's?
For the nrf52840 I've found this documentation: https://infocenter.nordicsemi.com...
