We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi
I am working on a nRF52840 using Zephyr as OS.
I have setup some control GPIO pins in the device tree (se below). This works fine from the application. I can access...
When I enter 100 as the size for the ATT MTU all works perfect, but when I choose a larger number like 250 as ATT MTU, sd_ble_enable() does not return an error and I can debug...
I will be using an NRF5340-DK for starters. I have a Linux SBC that will be running blueZ. I can use USB, UART, or SPI to connect the NRF5340-DK to the Linux SBC. I am assuming...
Hi Dev Team,
I had installed the newest NCS version NCS v1.6.1 and was importing my application from 1.5.1 to 1.6.1.
However, I noticed a lot of changes with respect to...
Hi,
I have a question ,According to the official tutorial，I succeeded BLE OTA DFU in windows system by nrfutil ,however, when I use the nrutil tool to update the firmware...
I have tried to use I2C but it does't work out. nRF9160 doesn't start booting after executing "build and run" and pushing the reset button.
I open secure_boot project...
Hi Nordic team
At sdk connect sample/mqtt_simple, it called lte_lc_init_and_connect() to connect NBIOT or LTE-M.
If this call was not successful, could we read error code...
hi support team,
very strange question from customer
customer set up one interrupt with following code:
void gpio_wakeup_init(void) { uint32_t err_code; if (!nrf_drv_gpiote_is_init...
Hello, I am routing the NRF52840-QIAA chip and wanted to avoid the costly via-in-pad process.
Can I use the following pins for QSPI quad mode?
Also can i leave the RESET...
I have a working set of implementations placed in the 17.0.2 SDK examples directory. The projects use SoftDevice s140 for BLE and flash write operations. I would like to know...
I'm looking to enable the flash protection for an nRF52 application running on Zephyr RTOS:
Basically looking to disable flash reads from the JTAG/SWD interface: Only...
Hello Nordic support,
I would like to understand regarding the status value 'ZB_ZDP_STATUS_NOT_SUPPORTED'.
I have a Zigbee application in which the device type is a Zigbee...
Hi,
I am using NRF52840 DK board. I am using SAADC example program for reading the voltage and SDK 15.3.0 Version.
We have connected the sensor to the adc analog output...
Hello Nordic team,
Our current setup:
nRF52840
nRF SDK v15.00
In our current setup, the steps we take are as following:
Initialize nRF52840 -> BLE fast advertisement...
I am developing a beacon for nRF52832 and can see the beacon in nRF Connect for iOS when using the following setting:
adv_params.properties.type = BLE_GAP_ADV_TYPE_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED;...
