Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi folks,
What's the maximum interrupt frequency the nRF51822 can support? I am looking to do an interrupt burst of about 4000 interrupts at a rate 2MHZ or 4MHz. In the...
Hello friends,
I am trying to flash a nrf51 dk with keil5. When I try to flash it with a multilink universal I get this error:
My settings are the following:
...
Hello !
I have a big problem !
I explain : am using the NORDIC nRF52840 board (as slave), to answer to a microcontroller (the master), using SPI. My nRF52840 has to simulate...
Hello.
Some months ago I open this thread .
Yesterday talking with one member of android team, told me that the problem with "pairing/bond" persists with few Huawei phone...
Hello everybody !
My code is based on the code of the "ble_app_template" to which I added my own custom service composed of 4 characteristics sending notifications. Notifications...
Hello Nordic developer, I'm asking my self if it's possible to use a task of one timer like STOP TASK or START TASK as PPI event ? For example, like that :
I expect that...
how can i program in nRF 52840 UARTE. i want to communicate with other serial device using nRF 52840 UARTE communication (send and receive data).
can you send me the snippet...
Hi,
I am developing an ANT+ embedded device (nrf52832, SDK14.2) , that (among other things) acts as a BSC receiver. I have a BCS sensor that is seen in Garmin Edge as 136150...
I want to transfer data using UART to BLE by Baud Rate 19200(using nRF51822).
Transfer data speed need to achieve 2KB/sec up.
How can I do it successly?
Thank you...
I noticed that you have a branch called feature/v6-upgrade for pc-ble-driver. Is that branch usable for 52840 and s140?
By usable, I mean it can be mostly usable and we...
Hello,
I am following the PPK Get started get started of the PPK board.
I am developing on the NRF52-DK (Rev 1.1.0 2017.23) - nrf52832 My SDK is the nRF5_SDK_15.0.0_a53641a...
Hello everybody,
I am using sdk14.2, s132 with Nrf52832. I want to define the pin of the NRF52 as the input and decode the incoming pwm signal. For example, I have a signal...
Hello,
I am working with the BL652 EVK from LAIRD. The EVK has nRF52832 IC inside of the module. I downloaded the " nRF5_SDK_15.0.0_a53641a" and trying to use "ble_app_uart_pca10040_s132...
