Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
When using jlink to connect to my board in VSCode, it displays "unknown device"
nrfutil device recover
I tried a few of my boards, but the result was always the same...
Hi everyone,
I’m working with Zephyr 3.2.3 in a Windows environment and trying to run the shorter connection intervals sample: https://github.com/nrfconnect/sdk-nrf/tree...
Hello Nordic Team,
We are trying to test an external audio DAC (TLV320DAC3100) using the nRF9151 DK .
As a first step, we attempted to build the i2s_output sample from...
Hello Nordic Team. I'm currently facing an issue when building in release mode (CONFIG_LOG, SERIAL, CONSOLE disabled). The issue is that after a random time (no longer than...
As shown in the figure below, I measured a voltage of 5V at the location marked in red, and measured a voltage of 0V in the components within the yellow box。
Is it absolutely...
What is the switching frequency of the internal DCDC in 54L15? What is the function of the FB1 ferrite bead in the reference design? Are there any risks in changing the capacitance...
I am extending one of Qorvo's UWB platforms.. adding Softdevice BLE functions.. (which work ok) (this is on sdk 17_1_0)
the coprocessor uses a GPIO connected signaling mechanism...
Hello!
We are a student group from NTNU which is developing an BLE Audio Beacon using the nRF54L15 socket and the nPM1300 PMIC. However, we have ran into some issues when...
Hi, I am trying to optimise for raw TX throughput. I am running the raw_tx_packet sample. I am using a nrf7002-dk and running v3.1.99 with the following configuration changes...
Hello,
I am currently working with the Nordic Power Profiler Kit II (PPK2) and the Nordic Thingy:53 for current measurement experiments.
Setup
I was using PPK2 to...
Hi,
I'm trying to use the bitcounter to drop packets that don't comply to a specific UUID. I'm working with nrf52840.
My question is - if the received packet is shorter...
I’m working on a custom board based on the nRF9160 (SICA variant) and trying to enable MCUboot + TF-M with sysbuild. I’m running into an issue where the system never reaches...
If a device has established a PDN connection, is it sufficient to rely on lte_lc's pdn module to determine if a network connection has "failed" due to being out of range,...
Nordic Team:
We have a product in production that uses the nRF9160 and nRF7000 and had assumed the nRF7000 did not transmit. We only recently discovered that it does, in...
Hi
How can I use ztest to calculate code coverage on the nrf54l15 platform, I tried to use the configurations of CONFIG_FORCE_COVERAGE=y, CONFIG_COVERAGE_GCOV=y, and CONFIG_COVERAGE...
