I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello,
I am trying to flash a custom software to a NRF52832 DK.
The DK is powered by USB and i've connected as follows :
VDD(nrf) to Vref(J link)
SWDIO to SWDIO...
I'm developing a central that may have to service more than one peripheral concurrently while (occasionally) advertising its own peripheral service. Things seem to work OK...
Howdy Nordic, hope that you are all well and safe.
Herewith I am reporting a bug I saw in the nrfMesh mobile application.
Information:
nrfMesh V3.1.6
Samsung Galaxy...
Excuse me
1、How can fast lte-m link have Ephemeris and Almanac?What is the principle?
2、Why provide current and neighbor cell information?What are current and neighbor...
Hello people,
I had to make a tiny, 4 layer PCB based on an nRF52832 chip (WLCSP) and I've chosen to use a PCB antenna. I've copied the reference design (nRF52832-CIAA Reference...
Hello,
I'm programming a nrf5340-dk using nrf sdk connect 1.6.0 and i wanted to change the publish address in order to be able to control multiple nodes using only one...
Hello everyone, I am using NRF52840 development kit and have implemented RTOS in it. I found that the floating point calculations are not working properly. In build settings...
Hi Nordic team
Q1. I am testing SDK Connect v1.6.0/full_modem_update. Pressed button1 to start download from S3 server. It was successful.
Then, it started to update modem...
Does anyone know what the power consumption of the radio peripheral on the nRF52832 is when it is powered but in the disabled state?
The product specification only offers...
Hi, i'm developing BLE nrf52832.
Is there any way to display the remaining battery capacity on that window 10 when connecting to Bluetooth like that picture?
The remaining...
Hi,
We are programming our devices (nRF52833) in production using a Segger Flasher Portable PLUS.
We use reset after programming via SFR access.
Our devices will not...
I'm using the at cmd library ( commands like at_cmd_write_with_callback ) to communicate with the modem.
I'm trying to enable the nrf_modem library to enable OTA updates;...
Hello
in order to analyze reboot reson (HW \ SW) I use the following:
in case of kernel crash I usually get coldstack print, in this case I can analyze and understand...
Hi guys,
Based on the examples that I found in Zephyr samples documentation, I created the program where I am able to measure the voltage and temperature, and then send...
I tried running pc-ble-driver-py/advertising.py
my command was " python3 advertising.py NRF52 /dev/ttymxc4" and then I got following error
Traceback (most recent call...
