Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi everyone,
I'm experiencing an unexpectedly long boot time on my nRF52840 device using NCS v3.2.0. Could you help me verify if this boot time is normal, or suggest any...
Hello,
We have the following environment:
1) nRF54H20-DK v0.9.1 and our custom board
2) nRF Connect SDK v3.2.1
3) Our simple project for testing BLE
4) nRF Connect...
MCU:NRF54L15，NCS SDK V3.2.4，android 7.0, nrf connect 4.26.1, cannot connect stably.
about 40 seconeds, the connect will disconnect, the android 7.0 side:reason is 0x08,...
Something seems to have broken in my VSC and/or Nordic extensions. Intellisense seems to be working for code, but cannot resolve any of my custom kconfig options.
I use...
I would like to sample a digital IO input from two IO's into the processor internal memory incrementally per every rising or falling edge of each of the signals.
Is there...
Trying to do ADV_DIRECT_IND advertisement.
We are trying to do the following advertisements
// ADV_IND Scannable and Connectable
// ADV_DIRECT_IND - Connectable...
I recently purchased an nRF52832 (XL52832-D01) for a wearables power management project. To test the module I flashed the basic blinky (zephyr). I'm using a ST-Link V2 as...
Hi
Brand new nRF52840-DK (PCA10056 rev 3.0.3, serial 1050245467, sticker on PCB). Never worked.
J-Link OB firmware update fails every time with: "Sending firmware data...
Hello! I am having troubles with my custom board using BL5340 from Ezurio. I have tried to flash it via my nrf5340 Audio DK but realized it doesnt support external Flashing...
Hi,
I am trying to set up a secure boot chain on nRF54L15dk with NCS 3.2.3 and an upgradable bootloader .
My intended boot chain is:
B0 / NSIB
S0 / S1 for the second...
Hello,
I would like to implement Device Firmware Update (DFU) over NFC.
Is this supported, and is there any recommended way to implement it? Are there any examples, reference...
I have two nRF52840DK boards that I was working with recently.
PCA10056 3.0.2 2024.33
I flashed one board with a BLE peripheral device code from the nRF connect sample...
Hello,
I'm using dmic module for sampling audio data from microphone. Recently I updated NCS to 3.2.2 and I started observing the following log: "Failed to allocate buffer...
After an update recently with the nRF Connect for VSCode Extension, it's been unable to find where my nRF Connect SDK is located when choosing a build configuration. It used...
