I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello,
I've been trying to modify the v2.4.0 Serial LTE Modem application sample for my nRF-9160 custom board, in order for it to communicate with our external MCU through...
Hello,
I'm currently running into issues when using the Logging Interface with USB CDC ACM. I tried to combine the cdc_acm sample and the console sample into one application...
Hello,
I measured the DC resistance between the RF output pin and ground pin and got around ~3-4 Ohm with digital voltage meter. This seems low. Am I missing something?...
Hi,
I have two nRF52833 DKs and both of them has connected to nRF21540 EK. I set the transmitter sending out 244 bytes data without stopping and measure it's current. The...
Hi there,
I want to debugging my beacon project card which designed with NRF52832 MCU
I have NRF54L15 PDK Development Kit and it has debugger on the kit.
How can I debug...
I'm studying the nRF Connect SDK Fundamentals course and working with the NRF54L15 PDK. In Lesson 1, I'm trying to turn on LED0. I can build and flash, but the LED won’t turn...
The nRF Kconfig extension ( https://marketplace.visualstudio.com/items?itemName=nordic-semiconductor.nrf-kconfig ) does not recognise some of the Zephyr kconfig extensions...
We are currently developing an ECG sensor patch that will operate over a cellular network, and we are considering using the nRF9151 for its LTE-M/NB-IoT capabilities. Since...
I'm interested in determining the current coverage enhancement behavior of a device, and I'm noticing a discrepancy between the AT+CEINFO and AT%CONEVAL results. Specifically...
as my last post issue nrf desktop in ncs SDK cant work when onnect to cmac os - Nordic Q&A - Nordic DevZone - Nordic DevZone .the ncs desktop cant work in mac os in nrf52840...
We are currently mass producing nrf52833. However, there is a problem with BLE communication. The defective product does not appear in the BLE search list at all. The failure...
Hi,
I'm working with UART with DMA(UARTE) on nRF52840. UART does not have HW flow control, just RX-TX.
I'm confused with DMA part. Is DMA circular or I have to reset it...
I have a nRF5340 using nrf connect v3.7.99-nc1 that is in a peripheral role. I establish a l2cap connection to the peripheral, to request a larger amount of data. That works...
Hello,
I am using nrf5340 audio sample with the custom board. The nRF Connect SDK version I used is v2.7.0.
I referred to this post and tried to add skyworks fem to my...
