I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi
I have thingy91x, which comes with two sim cards onomondo and conexa pre activated sim. i have connected sim and flash nrf cloud firmwware to see data on nrf cloud but...
Hi! We are failing to establish connection with third party devices (laptops, smartphones) in a couple of address-dependent advertising scenarios. The problem seems to be...
I have seen this assert since SDK 2.4.2 but less frequent. Now I had updated the code use the SDK 2.9.2, this assert made impossible to release it to production.
The point...
Hi Nordic team,
I am tring to make a BLE mesh net, I use two promicro(nrf52840), one for mesh_provisioner_example, one for mesh_on_off_app_example.
But mesh_provisioner_example...
Hello everybody.
I'm experiencing a problem with two nRF54L15-DK boards, one flashed with sensor clent sample (Client) and the other with sensor server sample (Sensor_srv...
NCS3.1.1, NRF52840, Windows, VScode
I have been trying to add MCUboot to my product, without success.
I believe there are known issues related to debugging when MCUboot...
I'm using the RTT log feature in NCS, and here is my prj.conf:I have two questions:
After using LOG_INF to output logs, I feel the logs are not output immediately. Since...
Hi,
I’m working with an nRF52840 that supports Bluetooth Low Energy updates via MCUboot.
We want to enable APPROTECT on our production units to prevent competitors from...
My understanding is that when the module's measured RSRP is lower than that defined in the broadcasted SIB, ECL will be escalated to higher level during RACH process.
Besides...
Hi,
I found out that my Matter device does not commission to Alexa because as part of adding the device Alexa will try to read FeatureMap attributes from all clusters and...
Hello! I'm working on some project using Fanstel BM832 module. I'm using the configuration based on board nrf52dk_nrf52832, with some minor modifications (led's and button...
Hi:
I'm doing the exercise L3-E1.
I used nRF Connect SDK Toolchain v2.7.0 because it didn't work with v2.8.0
How do I make NRF Terminal appear?
Thanks and Best...
I have a quick question about configure i2c.
I have the following schematic:
And the following configuration for the nrf54l15 :
And the following in prj.conf:...
Once the nRF52840DK is running the Zigbee light bulb demo I cannot flash new code to it unless I disconnect the board and reconnect it first.
I am using nRFConnect for Visual...
