Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi i just bough module E73-TBB(nRF52832) from EBYTE . I've already downloaded the sdk this link https://www.nordicsemi.com/Products/nRF52832/Download#infotabs
I test with...
Hi,
I would like to set up RTT on both net and app cores, but I haven't been able to get both running simultaneously. I'm wondering if this is even possible, and if so...
Hi, I am trying to get a working demo up for the Zephyr OS on your nRF52 DK but having trouble. See attached for description, I get this error -
-- runners.nrfjprog: Flashing...
Hi,
nrf9160dk device is not latching with CAT-M network. Please provide the solution for changing the "network mode" from CAT-NB(NB-IoT) to CAT-M in nrf9160dk device.
...
Hello,
I am able to program softdevice hex file with application hex file into nRF52840 microcontroller. However, I am not able to program softdevice and application hex...
Recently purchased nrf5340 to validate BT and BLE profiles.We have followed the guide and installed NRfConnect-3.7.0.
Installed BLE app and programmer app from nrfconnect...
I'm working with the latest v1.6.1 nrf SDK, and was able to get the Blinky sample code to work.. But trying to translate that to toggling other GPIO isn't working. I also...
I freshly installed Nordic Edition SES v5.50c and nrf sdk 1.6.1 on my machine and opened the empty_app_core with the Open nrf-sdk project option, selecting nrf5340dk_nrf5340_cpuappns...
While trying to build and run on my nRF9160 DK the project: asset_tracker , that I imported into SES by selecting: File>nRF Connect SDK Project...(in the SES menu), I followed...
Hello,
I have a ble nrf52840 module. I want to make it as becon code which is power optimized. Pls tell me the steps by which i can do that .Share some document or code...
hello ;
i need to send data from the nrf52840dk to / over the internet and to the server , so i know that on board nrf52840dk , there is no wifi chip on nrf52840dk , so...
Hi,
After the execution of erase all command(nrfjprog --eraseall) My custom board is not visible anymore. When I tried to connect with the nrf connect programmer ,I received...
This is the error I have. Couldn't figure out what causes this error. Tried all the related issues mentioned on this website. I have made sure the python and latest version...
The questions of data throughput:
1. nRF9160 supports SIM card for data transmission through NB-IOT, so what is the data transfer rate using NB-IOT?
2. Including data...
Hi, I am new to nrf.
l am using nRF5_SDK_15.3.0_59ac345
I am working on the ble_app_uart example and want to write the data in the flash of nrf52832.
I included flashwrite...
