Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi all,
Previously I spent some time to set up the nrfsniffer and with support I had succeeded; devzone.nordicsemi.com/.../setting-up-the-nrfsniffer
However as I have...
Hi
I want to modify the nrf9160 software samples from Nordic so I can use float with printk() and sscanf() functions.
I am also using gcc.
I try figure out how/where...
Hi,
As a part of FCC testing, I am trying use the following radio_tx_sweep_start(txpower,uiMode,channel_start,channel_end,delayms) with below parameters.
uint8_t txpower...
Hello, I have seen and heard of nrf52 alot that it can be used as payment card by using HCE technique. Can anyone please shed some light on it ? I want to know the way we...
Hi,
I'm running a nRF52832 connected through TRACE port to a Segger J-Trace Pro.
Some traces seem to be lost, and Segger support team tells me it is possible as nRF52832...
I have a few questions regarding AoA mode.
My goal is to append the CTE frame too a standard advertisement frame. I would like to use one of the following examples as the...
Hardware: nRF52840, running on dev kit PCA10056
Software: SDK 15.0.0, no soft device
I'm trying to get the POF comparator working, and after struggling in our product...
I just updated my project from SDK 15.3 to 16.0. I am using the nRF52840.
I am not receiving the APP_BUTTON_RELEASE event when waking up from a button press. It used to...
I am trying to the asset tracking application on nRF9160DK and following the steps mentioned in https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/getting-started...
Hi there,
I have tried to build mqtt_simple but ı got an error says:
#error bsdlib must be run as non-secure firmware. Are you building for the correct board ?
I am...
Dear Support Engineers
I am in the process of designing the automated testing platform for a 52832 based device and would like to test to make sure the components/devices...
Hi, I am trying to test the examples provided in nRF5_SDK_16.0.0 on nRF52840 (PCA20035) thingy91 device. But unfortunately, i didn't see the support files for pca20035. For...
I am using nvs_init(), nvs_read(), nvs_write() calls to store and retrieve user data. Everytime I flash a new image I use the following commands:
# nrfjprog -e -f nRF91...
Hi!
I was wondering about the Receiver Category of the nRF52840 according to EN 300 328. The device should be classified as a category 1, 2 or 3 receiver, based on the...
