Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hello Team, We are currently working on implementing a multilink connection setup using the nRF52832 and nRF5 SDK v15.0.0 for testing purposes. In this setup, we are using...
Hello Team,
We want to interface USB pendrive to NRF52833 and it will act as USB mass storage, where we can read and write data.
Is this possible and could please provide...
Hello,
This PR was closed without action:
https://github.com/nrfconnect/sdk-nrf/pull/16889
It says " you can always re-open " but the creator (my colleague) was unable...
Hello Team,
We are currently working with the nRF54L05 SoC and are in the process of enabling DFU over BLE. However, after integrating DFU support, we are encountering memory...
Hello,I tyed to install the CMSIS Wirzard in SES on the video from https://www.youtube.com/watch?v=b0MxWaAjMco But it deosn't work. I don't know why. I did read the DevZone...
We use an nRF52832 analog input to measure the voltage on a large capacitor. I think we have destroyed some chips when the capacitor is still charged and the power to the...
Hi,
I'm developing an application on the nRF54L15 and recently I designed a custom PCB with a sensor that gives interrupts when its FIFO is full (should be around every...
I would like to develop an application with Nordic's nRF8001 DevKit. The master emulator of this kit is an USB Dongle and it is originally meant for PC connection. My final...
Hello Nordic Team,
I'm experiencing issues when trying to flash my Matter application to the internal flash of the nRF54L15. I've followed the guidance from this forum post...
Hi,
I am using an nPM1300 together with an nRF5340 and an LIS2DW12 accelerometer. The nRF is powered from VOUT1 on the PMIC, and after some time of inactivity it is turned...
Hi
I am developing some nodes that all using BLE in nordic chip, I want each node get some data at the same time and send to one central device, the central device can fuse...
Hi,
I am wondering whether I can have one "RELAY" device in BLE communication (not BLE mesh), I have look through this forum but only saw some example 5 years ago. As I...
Hi Support team
1) What is the actual minimum operating temperature of nRF51802?
2) Could you help clarify more details about the temperature sensor(TEMP) of nRF51802...
Hi,
Our team is trying to disable the Access Port Protection (APPROTECT) for the nRF5340. The main goal for this is to be able to start breakpoint debugging without needing...
