HI,
I am using the NCS V2.9.0 ,nrf Desktop sample;
I want to mouse can pair 3 hosts, and i can select one of them connect and work;
I set CONFIG_BT_MAX_PAIRED=3 and...
I have a custom nRF52832 board with outputs on P0.07 P0.08 P0.09 P0.10 and I want to write to them. 7&8 are working ok but 9&10 are not.
Let me emphasise THE BOARD IS WORKING...
Dear Nordic and community,
I am currently in pre-production phase of designing a PCB based on the NRF9151, and I am a bit confused by the Hardware Device Guidelines, which...
Hello everyone,
I'm trying to set up the Wifi stack on the nRF7002 and use it with MicroPython, but encountering a lot of difficulty with it. I cropped up a network_wlan...
Hi all,
I have a custom board build with an nRF9151. I'm able to connect on int with USB/UART, I can send and receive AT command. Right now I'd like to send certificat to...
Hello, I'm developing a BLE Central application using the nRF52 SDK. The central connects to multiple peripheral devices (nRF52832), each sending 6-byte ADXL345 accelerometer...
I'm having trouble getting the I2C interface working on our nRF54L15-based prototypes. The initial config write to the device fails; specifically, in the twim driver (i2c_nrfx_twim...
While going though the Makefile of the FreeRTOS HRS example in SDK 16.0.0, I noticed this part:
By default, link time optimization (LTO) is not enabled.
If I enable...
After Christmas update we are unable to use DFU from Android devices.
We've been using such function on a regular basis with our devices and everything has always been fine...
Hello everyone,
I'm using a NRF51822 as a central device, I connect to a peripheral (NRF51822-based device), then I stop the scan. At a later time I initiate another scan...
Hi,
I am trying to program nRF52832 custom circuit with nRF52 DK, I have connected debug out from the nRF52 DK to the custom circuit containing nRF52832 debug in. When I...
Hey Guys,
i am currently experimenting with the NFC functionality and have an issue with our "nrf52840-DK" boards:
i am testing with IAR (8.40.2 - including the library...
Hi there,
I'm trying to use serial library from SDK to interact with cellular modem (AT commands, not nRF9160). I've read documentation (library description, api). May be...
I have build and flashed the zephire/sample/bluetooth/hci_uart on nrf52840 board and connected the board with ubuntu but hci interface was not created when checked using hciconfig...
Hi,
We have chose LCD which has only 3-Wire support CS, CLK and DI so we have connected that pins with nRF51822 chipset. Now Please see the below image which shows that...
Hi All,
I want to read/write long characteristic (200 bytes max) from Android to my device.
I'm working on the 15.2.0 SDK and S140 Softdevice.
I read some Q&A on...
Hi there,
Right now I am doing some dry research into long range Coded PHY for S=8 or S=2 since I need to have some extra room in the link budget to go the distance. The...
Hi, I'm trying to adapt the ble_gateway example for nRF91dk to use a nRF52 instead a Thingy52. When I change the UUID at ble.c from Thingy to nRF52, I'm not able to get a...
Hello guys,
In next few months I've to put down a new design for a medical product. Both nRF52840 and nRF5340 would fit well the application requirements. But I think this...
I want to use two UARTS ie uart0 and uart1. I read that nrf51822 gpio pins can be set as rx & tx but i couldnt find any example.
I am using SDK12.3
Please attach some...
