I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
Hi,
I have nrf9160-DK and I am using NCS v1.6.1. I am trying to run HR Peripheral sample application on the nRF9160DK board.
I have flashed nrf52840 with hci_lpuart sample...
I am trying to using nRF52833 and nRF52840 as a BLE central to connect customer's BLE peripheral.
The attached screenshot is the service discovered by nRF connect Android...
Hello,
I am developing an application based on the BLE examples from the nrf5 sdk using he Segger Embedded Studio.
I am porting a library for a peripheral component and...
https://devzone.nordicsemi.com/f/nordic-q-a/80125/want-to-achieve-1-2-mbps-through-ble
Issue is in this link is not properly addressed . I want to work on BLE with good...
How much i can apply maximum and minimum voltage at Analog pin of nRF52832 controller IC? And Please also guide me is there any mention in the nRF52832 Datasheet.
Hi all,
I am using SDK = 15, softdevice = v6, chipset:nrf52810
I have used ble_app_uart and SAADC example code for one of my application, its working fine, and next i...
Hello,
I'm using nRF v1.5.1 SDK.
If I have my RX buffer to be of size say 6, and I transmit 7 bytes then my code will detect a full RX Buffer and go to the endrx_isr...
Hello,
Looking at the errata entry [78] TIMER: High current consumption when using timer STOP task only , I see that it recommended to use TASKS_SHUTDOWN instead of TASKS_STOP...
Hi everyone,
what are the tolerances of the internal reference voltage of the ADC (0.6V) at room temperature? I know the tolerances are included in the gain error and are...
Hello,
I'm following this documentation Doc to include Fota upgrade on peripheral LBS sample but I have the following problems:
1) all file .bin like ( app_update.bin...
I'm using dongle nRF52840 to sniff packets between earphone & iPhone.
I am facing the same problem: " Encrypted packet decrypted incorrectly (bad MIC)"
just after LL_ENC_REQ...
HI,
I'm developing it using NRF52832.
I'm updating the remaining battery capacity using saadc. However, the battery value is not stable because the value obtained from...
Hello,
Following to this ticket , I started with an existing Segger embedded studio project from the SDK to port my project from Keil to SES 5.62 .
Now, the project works...
How long does it take to perform a soft reset (using sd_nvic_SystemReset()/NVIC_SystemReset())?
Looking at power measurements (attached) it seems to take about 730 ms (...
Hello developers,
I would like to combine BLE Central with USB HID. I am using the SDK example "BLE_Central_multilink", I can get signal from BLE modules.
Now I want...
