Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi all,
In the PDF version of nRF54L PRELIMINARY DATASHEET v0.8, in chapter
9.1 Debug access port: in table 65: Access port overview
is listed AUX access port of AHB...
nRF5340Dk with NCS 2.6.1 and toolchain 2.6.1.
I want to measure 6 frequencies for my application, these frequencies would be attached to GPIO pins and needs to be measured...
Hi, I'm learning the nrf51-powerdown-example <system_off_wakeup_on_gpiote> from github.
My understanding of the code is:
1) When button 0 (Power down) button is pressed...
Hello, trying this and that with a qwiic relay , first a test on i2ccl then VS using a 9160DK. (i2ccl -> pip install i2cdriver ) returns a status of 0x00 that relay is not...
NCS 2.7 with sysbuild + mcuboot
NRF52840 (custom boards)
In my previous projects with NRF5 SDK I found it was very helpful to define a section in the linker so the rtt...
Hi,
I have a two part question aimed at optimizing the battery life during BLE transmissions. I am using an nRF52805 with the S112 soft device and a DCDC regulator connected...
Hi,
We have a custom board with a nRF9151. We're still sorting out LTE connectivity issues but I wanted to try out the location services with GNSS only for now. I modified...
I am building a Bluetooth controller with channel sounding feature enabled. The project uses an external Bluetooth host along with the hci_uart example. The prj.conf file...
Hello, I am using nRF Connect SDK version 2.9.0, and I want to know how to perform the software interrupt.
Where can I find the driver of the software interrupt to know...
startup_config.h is included in the file 'arm_startup_nrf51.s' but it does not exist in the nrf5 SDK. Where is it located?
I note there is a comment about the nrf5...
I have the same application that runs on both nrf51 and nrf52 MCUs. The Bluetooth in the application uses SoftDevice and not the SDK primarily because I started with the pc...
While evaluating low power mode on SBC I notice something strange:
- PPK II measuring 76mA
- LAB power supply measuring 67mA of supply current
- Digital multi meter...
I have nRF Connect SDK v2.9.0 and an nRF54L15 DK.
Is it possible to build the Zigbee NCP Sample for this board?
The source files under the Zigbee NCP Sample directory...
Hello everyone,
I have zepyhr running on the Cyclone V according to the following instructions: https://docs.nordicsemi.com/bundle/ncs-2.5.2/page/zephyr/boards/arm/cyclonev_socdk...
Hi,
I am using the SAADC (AIN2) to get temperature values from a Pt1000, and I am experiencing sometimes strange behaviour after the offset calibration is done.I have quite...