I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi
According I2C standard, there is a requirement regarding falling speed of SCL/SDA which is > 20*1.8/5.5=6.54ns, and our measurement result of Tf on SCL is 5.732ns.
...
Hi
I am using the nRF7002 DK with NCS 2.7, based on the sample project `nrf70-wifi-ble-image-transfer-demo`. I modified the code to embed a fixed image as a header file...
Hi
In nRF5340 datasheet I2C frequency only have 4 selection as below
But when ask your AI, he response below
Important errata at 400 kHz
For all nRF5340 revisions...
I would like to trigger a hard reset when valid voltage is first detected on VBUS. How could I do this with no or minimal external components and without a complementary MCU...
We are using the nRF54L15 SoC with FOTA functionality. We have enabled secure FOTA by signing the firmware image and provisioning the public key into the SoC’s KMU. For production...
I'm running the subrating sample (ncs\v3.1.1\nrf\samples\bluetooth\subrating) on two nRF54L15-DK boards.
I'm puzzled by something I can see through my protocol analyzer...
Hi,
I’m working on a distributed testing pipeline where tests are built on one machine, but executed on a separate, lightweight container that does not contain the full...
Hello Nordic Team and Community,
I'm working on a fully automated Zephyr RTOS development environment on Raspberry Pi (Debian Bookworm) targeted at the nRF52840 Dongle....
Hello,
Is it possible to get logs (RTT) from an application started by a bootloader? As of now I don't get anything after the bootloader has jumped to the application start...
While running the BLE HCI USB ( bluetooth_hci_usb ) sample in Raw mode on an nRF52840 board, we observe a bus fault under specific conditions. The fault occurs when the device...
Hello everybody,
I am a research assistant at a university , responsible for maintaining and porting existing student lab exercises from the legacy nRF5 SDK to the nRF Connect...
Background:
My project is using the nrf54L15 with the 48 pin package. I'm using vscode with v3.2.0. The QFN48 package has the following pins bonded from the silicon to the...
I am trying to receive extended advertising from a device on nRF52832 .
I have made the following changes:
sdk_config
# define NRF_BLE_SCAN_BUFFER BLE_GAP_SCAN_BUFFER_EXTENDED_MIN...
