Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I'm finding problem to generate the library uECC.a to use in project secure_bootloader for nRF52833 (SDK17) using SEGGER.
I started from project SDK_17\examples...
i want that my device shall advertise after i press a button for 5 seconds. there is a feature of long press for button kindly assist as how to use this for advertising
Hello,
I am currently trying to combine the NRF52840 (Development kit) with the Arduino Ethernet shield containing an W5500.
I was wondering if there is any example...
I have been trying to figure out how to use SPI on nRF Connect SDK. I cannot find a simple enough example to get started other than the convoluted SPI flash example or the...
We find a Beaocn from other distributor , it got very less fluctuations. RSSI table show below.
Test method: 10 RSSI were collected from a hand-held mobile phone at...
Typically the Base address registers and Prefix registers are used to configure up to 8 logical addresses and then RXADDRESSES is used to filter which of the 8 logical address...
Hi,
The new AT monitor have a hard-to-reproduce bug: the subscriber entry list alignment is not specified in the linker script. Since structs are always aligned, that means...
Hi,
im porting our nrf9160 application from SDK 1.3 to SDK V1.6.1. and facing error while accessing NVS device in SDK V1.6.1.
in SDK 1.3 i used "device_get_binding(DT_FLASH_DEV_NAME...
Hi,
I have have certain thread that I would like to be active during a ble connection. I can suspend it when not needed and resume when connected. But as long as the thread...
Hi:
I'm using SDK V17 & encounter a problem.
in my project, the nRF52832 doesn't broadcast at all.
Once the button1(EVK btn1) is pressed and lasting 5 seconds,
nRF52832...
I'm very new to the NRF boards. I can not find any information on the USB port (programming port). I would like to use that to read serial data written from a terminal program...
I am using the nRF 52840 development kit to explore Thread. I am using the 'open nRF Connect SDK' command to get the project. I would like to use the 'overlay-usb.conf' option...
Hi,
I am also facing same issue i am able to read the version register correctly and able to perform self test successfully
I am using 17.1.0 n RF5 SDK
I am developing...
Hello Nordic Devzone Community,
My name is Ted, and I recently posted a question here regarding trouble when attempting to flash a Sparkfun Thing Plus nRF9160 board, using...
The connection is established but no data is transferred between the nrf52840 and the mobile phone(android10). But on android7 or android9 there are no such problems, everything...
