I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
Hey.
I have a problem where the task watchdog times out immediately.
I have taken the samples/basic/task_wdt sample and modified it a bit to simulate what I have in...
The environment setup I'm using is VsCode with the NRF extension. I'm using SDK v2.6.1. When flashing bootloader firmware to my device I get this output on my vs code terminal...
minimal_log % west flash -- west flash: rebuilding [0/4] Performing build step for 'mcuboot_subimage' ninja: no work to do. -- west flash: using runner nrfjprog Using board...
We have fairly regularly observed that the reset reason register gives two reasons for reset: software request and watchdog.
Is it plausible that these bits are genuinely...
Hi,
I am trying to communicate with nPM1300 PMIC board using NRF5340DK. I have made the connections and set up the overlay file as recommended. The I2C write (i2c_write_dt...
I am currently developing software of the nrf9160 and am having trouble with a firmware upgrade. The firmware data is received via UART. All of the functions work as expected...
Hello all,
I am working on a ble application on zephyr. I need to send a notification on a specific characteristic.
If I call bt_gatt_notify from where I want to send...
We're currently using a virtual operator as carrier, so our device is roaming in Finland. It seems that Elisa (24405) is the preferred network, but the data plan is restricted...
Hello, can 2.0nH or 1.8nH inductors be connected instead of the 1.9nH inductors connected to the ANT1 and ANT2 pins shown in the NRF21540 reference circuit?
After getting nrf52 board I've sucessfully recovered it, flashed it with blinky example and I cannot recover it again. I tried doing nrfjprog --recover and nrfjprog --family...
I'm working on a custom board that uses an NRF52840, I've followed the Nordic Developer Academy course related to DFU over uart0 ( Exercise 1 - DFU over UART - Nordic Developer...
Hello everyone,
I have a custom board with a nRF5340 on it that is used as a BLE reader for mobile phones. Now we wanted to do some EMC testing. For this we need to broadcast...
I am developing a board with the nrf5340, and using a PDM microphone for audio input.
I have used the same microphone on the nrf52832 with the nrf PDM driver with success...
Hello Nordic team!
I'm currently trying to get a demo of zephyr's Blink up and running on my Thingy53 device so I have an understanding of how the connections between...
Hello,
I’m working on an nRF5340 project and trying to measure power consumption in low power mode using SDK v2.6.1. I followed the instructions provided on your website...
