Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
Hello everyone. I work with nrf52840 chip and previously I had an app with softdevice (s140) and use BLE bootloader. Everything works as expected. Next I want to use another...
We are using ncs 2.6.0 and nrf5340 audio dks.
Sample is nrf5340_audio broadcaster.
One dk is configured to work as Audio Broadcast BIS Source and other as Sink. By default...
Hi there,
I am working on an audio recording and transfer application using nRF5340 (microcontroller development kit) and SPH0465 (digital microphone with I2S support...
Hello, I have designed my own board based on NRF52840-CKAA-R, which uses USB power supply. The working voltage of NRF52840 is 3.3V, and my test voltage is normal But NRF52840...
Hi,
I've ready many threads and docs on NRF52 SoC Revisions and Softdevice support but I am still confused. So apologies if I ask something which is already asked.
From...
Hi,
I want to implement low-power mode in my nRF5340 application. From what I understand, Zephyr's idle task automatically handles entering sleep modes, and the device wakes...
Hi,
I am evaluating warm and cold reboots, I am seeing no difference between them. I tried tracing sys_reboot definition, ended up with
For arm core with no handling...
As described in the docs.nordicsemi.com/.../powersave.html: “The application must choose the right duration based on the traffic pattern. Applications must also take appropriate...
Hi, I am using nrf9160 DK development board, i want to use gpio pins in this kit for a SPI interface from nrf52840, which pin i can use for this purpose. in datasheet it very...
Hello Nordic Team,
I am working on integrating the nRF21540 RF Front-End Module (FEM) with the nRF52840-QFAA in the 48-QFN package. Could you please provide the following...
Hi, I have reviewed the light_bulb app code in NCS2.8.0(include src code/CMakeLists.txt/prj.conf and so on)。 But I can't find where the path of matter is included, could you...
Hi all,
I wanted to enable read/write protection for MCUBOOT partition in my firmware from the application and encountered a strange problem. The build (build system - default...
Hi there,
This almost certainly has a simple answer but I can't work it out. I'm using the sample WIFI Scan for the above boards and can successfully scan away. But I'd...
Hi there, I am new to working with UART. I have managed to load the Nordic UART Service Client(Central) and UART Serial Port Emulation(Peripheral) without any sensors attached...
