Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I am encountering difficulties connecting to and recovering my nRF52840 board with J-Link on macOS, both via nRF Connect and using nrfjprog in the terminal. Below...
Hello,
We are using the nRF52840 dongle (PCA10059) with the CLI agent software as a Zigbee network coordinator, and the Digi's XBEE S2C as a Router.
We are using XCTU...
Hi Team,
I have nRF5340 DK board and I want to test the Bluetooth Periodic Advertising with Response and Bluetooth Periodic Advertising with Responses Synchronization...
Hi,
I am trying to create a new custom service in nRF Connect for desktop and play around with its characteristic properties.
I Use an nRF52840 DK as peripheral and my...
Hi,
Its maybe a stupid question but is there a easy way to operate the DK with 3V VDD and IO Voltage? The 9160 DK had a simple switch for this. The default for the 9151...
Hi everybody I'm using nRF Connect SDK 2.6.1. Before I could seen Partitions section in Memory Report tool, but now it's disappeared. I also checked it by ninja command: ...
Hello,
I have a few questions: 1. How to add a prj.conf or an overlay file to enable peripherals to use an external high-frequency crystal oscillator as the clock source...
We have developed a firmware application using the OpenThread library for the nRF52840, utilizing the Nordic Development Kit and Segger Embedded Studio for ARM (version 5...
Dear nordic support team,
after having migrated my project to SDK release 2.8.0, the following message appears in the logs:
<dbg> bt_sdc_hci_driver: configure_memory_usage...
"I'm working with nRF Connect SDK v2.2.0 for nrf52840 and I'm trying to implement file transfer functionality using mcumgr over UART in Application. I've successfully configured...
Hi , I flash periodic_sync_conn sample to A and B development boards, and periodic_adv_conn sample to C development board. Only A and C development boards work normally, but...
Hello. We are developing custom boards with the configuration of nrf5340 + nrf7002.
In the previous sta example, a build error occurs when the "Board Target" in "build configuration...
I have customed my own nrf54L15 board and it would run on button battery. I managed to measure the battery level through ADC, but I don't know how to use ADC with nrf54L15...
I've been working for months to try and figure out exactly how to get my application to bond the way I want it to.
I'm using nrf connect sdk 2.4.2 on an nrf52832. I used...
