Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
I am currently working on a project involving the Nordic nRF52840-DK development boards (1 Central and 11 Peripherals communication), with LE PHY Coded S8. In this project...
Hi,
I’m using an nRF52840 SoC and currently developing with NCS 1.8.0 . I need clarification on the Bluetooth Core Specification version support :
What Bluetooth version...
Hi Nordic，
I am using the nrf52840 as the host and the nRF9160 as the modem with the serial_lte_modem library.
Normally, when the nrf52840 sends an MQTT connection request...
Hello,
I am planning to design a custom board using the nRF5340.
My main question is: How can I view log messages from source code running on the custom board on my...
hello,
I have a neo pixel running on my nrf52840 using SPI. I still require the SPI clock pin to be configured to a pin even though it is unused. This wastes a pin, is there...
I took the example of peripheral_hr_coded and central_hr_coded. I flashed these examples in nrf52840. They communicate normally. However, the Advertising Packages are not...
Hello,
I'm using the zboss stack to implement a zigbee end device on nrf5340.
My device is able to connect to a zigbee network and to notify sensor events on zigbee but...
Hello, I am using the LIS2DH sample (and the st,lis2dh driver, which is compatible with the LIS3DH accelerometer) to test out a LIS3DH IC attached to a custom board. However...
hi i use pca10056 board with segger embedded studio
i currently facing a bizzarre problem with my project
i use adc function and nus service and low frequency clock
...
Hello i realize the nRF24L01P is NRND. Curious if you are able to answer w/out too much work as to whether one of the other nRF devices allows access to the radio to use the...
Hi:
I set up a fresh install of the NRF Connect Extension Pack in VS Code on my MacBook Air M4 and was able to build and flash the Blinky demo to my nRF52840DK. The issue...
Hello, this ticket addresses three issues:
1. After installing nrfutil with subcommands device and toolchain-manager and sdk-manager, into %USERPROFILE%\.nrfutil, everything...
Hello,
Since our Product Launch we have gotten feedback that pairing with some (but not all) Apple devices is a significant problem. Even through several attempted fixes...
After upgrading nRF Connect SDK from 3.1.1 to 3.2.1, our fixed regulator stopped working. We are on nRF54L15. Tracking it down further, this seems to be some sort of GPIO...
Hi,
I am porting a product from SDK 15 to SDK 17 and to Nrf Connect.
We need to maintain code combability as far as possible between products using SDK 15/17 and products...
