Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
Hi everyone,
I'm working on the nrf51822 chip and using S110 stack of SDK 6.1. Everything is fine for IPhone5s. The proximity example is running on the nrf51822 device...
i have given shell command through RTT and its working fine but when i try to start distribution, i am getting below error
Please advise me how can i fix this error.
Hi,
We are using Bitbucket as our CI system, and our project is based on the nRF5340. I can compile the project locally in VS Code without any issues.
Previously, we were...
I am trying to build the code for AOA example for nrf52833dk_nrf52833 dk from the example code avaliable on the sample called direction_finding_central. i have nrf connect...
Hi,
This is my first time designing RF section for BLE using nRF54l15, and i was wondering if you guys can give me some feedback on hardware design. I chose a Johanson 2450AT42B100...
Hi!
After some work with the otherwise exceptional Power Profiler software I find the current screen layout annoying:
The current display is in sync with the digital...
Hi,
I like to measure the VDD in nRF54L15DK using ADC.
I have flash the example firmware ..\v3.1.0\zephyr\samples\drivers\adc\adc_dt in my DK.
I can see it is measuring...
Hi, Good day!
I’m currently working on the nRF52832. The requirement is to support BLE + LoRaWAN (SX1276) .
I have a few questions:
How can I set up the LoRaWAN...
Hello, I have a question about the power consumption stabilisation of the nPM2100. We configured the nPM2100 with the pins directly to obtain a V_OUT of 3V with a 2477 battery...
Hi,
We are currently considering the performing DFU with UART with another MCU. Is there a sample for this application where nRF54L SoC is being updated by another embedded...
Hi,
We are evaluating NRF5340+NRF7002 setup for our customer. We are currently using https client example(sdk v3.0.2) and we would like to benchmark current consumption...
Hey everyone,
I have designed a custom board with a bunch of nordic IC's (nRF54L15, nRF9151, nRF7002 & nPM1300)
I have tested the basic functionality so far, including...
I enable cs procedure and set the procdure count equals to 3, let procedure interval to be 10.
I want to change the cs channel map between procedures. so when I send HCI_LE_CS_Set_Channel_Classification...
Hi everyone, I am attempting to measure I2S rate against internal clock frequency since I am using APLL. I am following examples in NRF5340_Audio application. What i have...
Currently, I'm using the NRF5340 chip. In my own development board, I'm only powering the chip to test its transmission performance. The example program I'm using is the classic...
nRF52840 using Zephyr 2.0.0
We currently have a system that after we are running can drop to 20uA. However, on boot, we draw something like 5-7mA. This large on boot current...
