Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
2. In the nRF sniffer software, the device I'm interested in does not show up in the "Source" column with its addess, b8:80:4f:6b:b6:9e, but as "TexasIns_6b:b6:9e". It seems...
Hello,
I'm finding problem to generate the library uECC.a to use in project secure_bootloader for nRF52833 (SDK17) using SEGGER.
I started from project SDK_17\examples...
i want that my device shall advertise after i press a button for 5 seconds. there is a feature of long press for button kindly assist as how to use this for advertising
Hello,
I am currently trying to combine the NRF52840 (Development kit) with the Arduino Ethernet shield containing an W5500.
I was wondering if there is any example...
I have been trying to figure out how to use SPI on nRF Connect SDK. I cannot find a simple enough example to get started other than the convoluted SPI flash example or the...
We find a Beaocn from other distributor , it got very less fluctuations. RSSI table show below.
Test method: 10 RSSI were collected from a hand-held mobile phone at...
Typically the Base address registers and Prefix registers are used to configure up to 8 logical addresses and then RXADDRESSES is used to filter which of the 8 logical address...
Hi,
The new AT monitor have a hard-to-reproduce bug: the subscriber entry list alignment is not specified in the linker script. Since structs are always aligned, that means...
Hi,
im porting our nrf9160 application from SDK 1.3 to SDK V1.6.1. and facing error while accessing NVS device in SDK V1.6.1.
in SDK 1.3 i used "device_get_binding(DT_FLASH_DEV_NAME...
Hi,
I have have certain thread that I would like to be active during a ble connection. I can suspend it when not needed and resume when connected. But as long as the thread...
Hi:
I'm using SDK V17 & encounter a problem.
in my project, the nRF52832 doesn't broadcast at all.
Once the button1(EVK btn1) is pressed and lasting 5 seconds,
nRF52832...
I'm very new to the NRF boards. I can not find any information on the USB port (programming port). I would like to use that to read serial data written from a terminal program...
I am using the nRF 52840 development kit to explore Thread. I am using the 'open nRF Connect SDK' command to get the project. I would like to use the 'overlay-usb.conf' option...
Hi,
I am also facing same issue i am able to read the version register correctly and able to perform self test successfully
I am using 17.1.0 n RF5 SDK
I am developing...
Hello Nordic Devzone Community,
My name is Ted, and I recently posted a question here regarding trouble when attempting to flash a Sparkfun Thing Plus nRF9160 board, using...
