Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hi,
SDK 0.4.0 simple_mqtt project
Modem mfwnrf916007029alpha
I want to write an unique 4 bytes ID into each nRF9160 via nrfjprog.
So that, I can set subscription...
If the peripheral makes a connection with the central (the peripheral sends a packet, the central responds, and the peripheral sends a second packet) What is the calculation...
Hi and happy new year everyone,
I am a developer for Raytheon Anschütz GmbH in Kiel Germany and working on a Zigbee mesh sensor network. Unfortunately I am an absolute beginner...
Hi, radio experts here. Due to some limited conditions I have to implement one custom radio communication pattern in MCUBoot, not the BLE stack which is a bit too heavy for...
Hi.
I have some question.
I use Thingy52 module.
I want to use(merge) all service in Thingy:52 SDK v2.1.0 into Nordic-Thingy52-mesh-demo in Thing_bridge.
I'm trying...
Hi,
I have tested the following solution and it doesn't work if I try to load more bytes.
case BLE_EVENT_DATA_COUNT_HANDLES:
printf("BLE_EVENT_DATA_COUNT_HANDLES\n...
hi
I want to know where the gazell control the GPIO06, i connect a LED with this pin ,and its blinky when send data failed .
I used to see it controlled in somewhere but...
Hello,
in my design I used the antenna swra117d from Texas.
I am able to connect to my custom board with the nrf52 dongle and the nrf52 DK.
Unfortunately I can not connect...
I followed the recommended steps and got the at_client solution to build and flash in Segger Embedded Studio with tag "v0.4.0".
I installed it onto my board, and but didn...
Hi,
I'm currently programming a custom board using a nRF52832 ( using this wiring ). Everything was working great but I tried to play with SAADC and maybe did a wrong...
I am using the link below
https://infocenter.nordicsemi.com/topic/com.nordic.infocenter.sdk5.v15.3.0/getting_started_softdevice.html#getting_started_sd
with 3 options...
I'm having some problems getting the sections/observers to work properly. Using SDK v15.3 and Crossstudio for ARM v4.4.2
If I break at ( nrf_sdh.c )
I can see that the...
Hello, I have just started using nRF52840 DK and previously I have used development kits from different vendors so, I was wondering when developing which resources are available...
Hi All
I know this is stupid but I can't figure it out - either I've missed something obvious or not connected something properly (or at all).
Using the PCA10040 nRF5...
I have developed a custom board with NRF52810 (Rigado), a standalone CAN controller (500 kbaud) and serial communication (57600 baud).
The SW is based on the BLE_APP_UART...
