[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
/**@brief Function for finding out whether a peer ID is in use.
*
* @param[in] peer_id The peer ID to inquire about.
*
* @retval true peer_id is in use.
* @retval...
Hello tech support!
I am using the built-in SPI to transfer the data. Also, I adopted the "timer" example in the SDK for handling the SPI transfer.
However, it seems that...
hi
I want to design Nodes for asset tracking. These Nodes will be spread out in a building. A moving object will have a BLE -Advertosor. The Nodes will detect Moving object...
Hello, I'm using the nRF51822_QFAA chip on a pca20006 board. I downloaded sample code from the offical site. Installed sample code nRF51822_beacon_firmware_1.1.1.msi. I use...
SDK: 14.2
64-bit Segger Studio 3.34b
PCA10040 Rev. 1.2.4.
64bit Windows 10
SD: S332
I'm trying to add the bpwr Tx profile to the ble_ant_app_hrm_pca10040_S332...
Hello fellows,
I did my master's thesis with the nrf51 and now some years later I need some help setting up a Laird BL652 to work with my beloved NRF+Keil tools.
Here...
I have a Nordic 52832 chip in an integrated module form from Fanstel. I have the NRF 52 DK, the Fanstel evaluation board, and a custom prototype board I built.
I can program...
Hi all,
I have ported my RTOS to nRF52832. It can run app and BLE properly. But when I measure the power consumption, the current is too high when BLE is enabled. Please...
Are the development boards for the 52832 certified for BT5? The 52832 chip is advertised as BT5 but the nRF52DK documentation says it is only BT4.2 compatible.
Thanks!
Hi all,
I'm interested in adding Infineon OPTIGA Trust X to nRF52840, but I can't found enough information.
Is Infineon OPTIGA Trust X hardware-compatible with nRF52840...
Hi,
I have connected STM32 with nrf52832 using STM:TX -> NRF:RX and STM:RX -> NRF:TX.
The communication works fine when i initialize UART on both devices.
The issue...
I am trying to implement a periodic calibration routine that is transparent to upper layers of my application.
I have the SAADC set up to continuously sample one channel...
Hello,
I was able to build the light_switch example using Cmake. But when I tried to build it using segger, I'm getting a board.h missing error. My build path is SDK_ROOT...
