Hi there is a problem in github.com/.../nrf51-UART-examples
any one can help?
I put empty loop in main, and comment off all ble related int. and I process uart_evt by...
Hi,everybody！
When i install master control panel 3.10.0.14, i can't find nrf.exe in " C:\Program Files\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf ". Only nrfutil...
Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hallo, we are evaluating the UART peripheral of the nrf54l15. As a first step, we are trying to get two DK to communicate with each other, unfortunately without success. ...
Hi all,
I'm looking at an issue and I can't get my head around it. I clearly do something wrong here but I'm stuck.
On our nRF54L15 DK we have a program that can show...
Dear Teams,
I’m using an nRF9151DK board running a simple firmware (example link: github.com/.../ subsys /pm/ device_pm ).
I connected a Power Profiler Kit II (PPK2) to...
Hi,
When I was developing, I found that the matter sample is a little different from the Bluetooth sample .
I want to disable CONFIG_THREAD_LOCAL_STORAGE in the Bluetooth...
Using a slightly modified version of the Zigbee Light Bulb sample app from the current samples compiled using nRF Connect for VSCode on a Mac and programmed to a nRF52840DK...
Hello,
I started off doing a v3.1.1 build and got this serious warning message
warning: BT_CTLR_DTM_HCI (defined at subsys/bluetooth/controller/Kconfig.dtm:14) was assigned...
This is a bug report for nRF Connect SDK 3.1.1.
The zsock_poll() method and hence also the poll() wrapper method https://docs.nordicsemi.com/bundle/zephyr-apis-3.1.1/page...
When following through the process described on GitHub for the NCS_SERIAL_MODEM I get an error during the build. I am following the steps described in the readme exactly as...
Hello Nordic Team,
We have developed a custom PCB using nRF9151 and nPM1300 . Sometimes, the PMIC powers up and works normally; other times it doesn’t start at all. It occasionally...
Hi All
I have a question here.gatt Characteristic uuid has been Modified After the equipment has been in run for some time.
Current conditions of the equipment:
1.The...
Hi all,
I'm trying to use SPI Slave on a proprietary Hardware that use Ezurio BL54L15 (that contain a Nordic nRF54L15 chip). The environment is VSC + nRF Connect SDK 3.1...
Hello Nordic team,
I’m using the Mikroe nPM1300 PMIC Click Board (based on the Nordic nPM1300 PMIC ) with an ESP32 over I²C to charge a Li-ion battery.
Setup details:...
Hi,
May I know if the ncs add-on sdk-ant also supported nRF52833 because it is not mentioned in the list. Thanks.
Compatibility — ANT for nRF Connect SDK documentation...
Hi,
I need to use GRTC channel 0 in a nRF54L15 project. Channel 0 is special. It is the channel that the INTERVAL register controls. `zephyr/boards/nordic/nrf54l15dk/nrf54l_05_10_15_cpuapp_common...
