Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hello,
I have an iOS application communicating with a custom device having a nordic 8001 chip.
They have established a bonded relation. In nRFgo Studio, in Security...
Hi there, thanks for your help in advance!
I have tried the nrf51-ble-ancs-nus sample from github and making it work on a 51822 EK board, i.e., it can receive notifications...
I try to use hcidump, capture CSR dongle on ubuntu14.4.
I can find SDK8.1.1 s110 keypad demo create connection fail.
HCI Event: Command Complete (0x0e) plen 4
LE Set...
I want to experiment with recording observations of the beacons with raspberry pi's.
Is there any precompiled firmware I can install on the nRF51822 smart beacon...
Hello everyone,
I am trying to communicate among 2 NRF24L01+ modules using 2 ATmega16A microcontrollers.
My SPI communication is working fine as I am able to write and...
Hi,
I am new to nRF Connect SDK. I am trying to achieve over the air Firmware upgrade through nRF5340. The SDK i am using is nRF Connect SDK v1.5.0 .
As per my understanding...
I am currently going through the usbd_ble_uart example and understanding what states make which LED's active,
Within the example, LED_BLE_NUS_CONN is defined as BSP_BOARD_LED_0...
How to use the internal 32.768k crystal oscillator for nrf5340？
NCS: V1.5.0
example: ncs1.5.0\v1.5.0\nrf\samples\peripheral\radio_test
Only HF no LF config.
Hi all,
I'm trying to use one of the built in sha256 libraries. As I've enabled the CONFIG_NRF_CC3XX_PLATFORM and CONFIG_NORDIC_SECURITY_BACKEND I thought I would pick this...
I am working on a BLE Product which connects to a remote device when detected within a certain proximity (based on the RSSI values). After switching on the scanning, I receive...
Hii Guys,
I am trying to run example code ble_app_uart on my nrf52810 sdk module . But when I try to run the code in debug mode I get an error of Vector Catch Error ....
Hi, I am working on nRF52840. I want to add GSM MQTT protocol. Is there nordic soc available for this? Which we can later communicate with nRF52840 peripheral device also...
Hi Everyone,
I am working on nrf52832, I am using sdk15.0.0 ble_beacon_app.
I want set tx_power but when softdevice enable gettting error.
I am tried using sd_ble_gap_tx_power_set...
Hi.
When I click add new LTE Device, I get the same menu as when clicking add new SIM Card. When is click register with IMEI and PIN assosiated to my nrf9160DK, I get. ...
Hello All,
I am developing a light control device using Zigbee and Alexa. I am using an nRF52840 device and SDK nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71.
For my development...
Hello Everyone,
I am a beginner
I am working on a project which requires authentication of the firmware , for this purpose i want to generate the hash of the firmware...
Hello OT Team,
I am working on the custom product where Openthread would be used. I am facing the issue while commissioning the other device to join the network.
The...
Hi ,
I tried following steps to configure and toggle GPIO pins.
I have also set CONFIG_GPIO=y i n your prj.conf file. ,referring to https://devzone.nordicsemi.com/f...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi,
I have followed the documentation here trying to get the radio_test project working for FCC certification:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom...
