Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
HI,
I succeeded in the test.:SPIM0 SPIM1 SPIM2.
I failed the test SPIM3.
Please help me configure SPIM3 init.
1. The SDK: sdk17.0.2
2. Example: D: \ Project \ nRF5_SDK_17...
I tried to use printf() to get the data from SPI buffers. It runs OK in the peripheral/spi example. But when I moved it to the ble_app_uart, the program stalled at printf...
Hi,
We are looking to upgrade our connect SDK version to 1.7.1 (from 1.5.1) but at the moment there are a few breaking issues for us that will prevent us from doing so....
Hi All,
I have a question that i remark this code run different mode have different results
in Release mode => build success,the project can run
in Debug mode => the...
Hello.
I have couple of questions for hardware parts location on pcb with nRF9160.
Q1.
I'd like to ask a better location for eSIM(MFF2) related nRF9150.
This...
I'm trying to add a second element to (light_switch\server) (SDK_for_Mesh_v5.0.0). I've already have a look at this post , it gives an idea but I found that it's not applicable...
In an effort to fix Toolchain problems setting up nRF Connect, I uninstalled Python and tried reinstalling via choco install python as per the "Installing Manually" instructions...
Hi,
Please fix this bug: The DK device is no longer found after following the following procedure
Problem operation process emerges
windows:
DK:PCA10090 0.9...
Hello,
I started my prototyping with the 52840DK and the SD Card was working fine. However, with the 5340 dev kit, I cannot get the SPI to work and access the SD Card properly...
Hi,
I connected my nRF52840 dongle to the laptop, it was detected with a red LED glowing on and off. Later I installed the nRF Connect software and installed the Power...
In our nRF52832 application, we have an external 32.768KHz crystal as the nRF52832 low frequency clock source. We also have a 32.768KHz oscillator on the PCB that is used...
Hello,
There seems to be a bug with scanning for many Bluetooth advertisements while simultaneously sending data over uart in Nrf sdk v17.
I have tried to work around...
When loading the nRF Connect Plugin for VCS, I am receiving either a crash message or the message below. It looks like a Python syntax error in the kconfig extension. python...
SDK 17
Soft device 7.2.0
nRF52840
Started with the 'fatfs' example, updated it to allow uninit, and to not reinit the IO if init is called multiple times.
it's working...
