How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hi,
In our application, we are using HID to control mobile phone or PC.When users connected our product, it will automatically connect next time.
But our product is battery...
Hi
I am using Zephyr samples (common with the samples found in NCS) to evaluate the advertisement function of nRF52833DK.
I have run these examples:
Bluetooth: Periodic...
Hi,
After updating the FW as shown on the video, LED3 is NOT blinking, trying to connect (LTE).
If I open the terminal window, select the board, and pressing the Reset...
Hi,
We are using the GPS xample for the nRF9160. and are struggling a little with getting the GPS fix.
$GPGGA,001932.00,,,,,0,,99.99,,M,,M,,*6F $GPGLL,,,,,001932.00...
Hello to all the Nordic Jedi knights!
I have a question regarding the PPK2: Is there a way to disable auto-ranging and manually select the measurement range?
I know that...
Hey,
I have a custom board with nRF52833. Sensor is connected to: P0.11 (pin 19) - SCL P1.08 (pin 17) - SDA
with code below I don't get any `NRF_SUCCESS` back.
I saw...
I'm trying to build a new device that I bit, bang the I/O Also others to just have simple signal controls.
Below is the portion of my dts file. The example here is the onewire...
Hi,
I am using nRF52810 (s112 softdevice) with SDk version "17.0.2".
How do I set BLE advertise in continuous mode(if not connected then advertise continuously until it...
Hi
I am trying to declare a custom cluster in zigbee and enable the reporting for some attributes of the cluster, i followed this post to create the custom cluster devzone...
Hi guys,
I'm researching the maximum direct connection distance between two Android phones for transfering small amount of data - which lead me to BLE Coded PHY S8 as a...
Hi,
I m using nRF52840 dongle to setup the nRF5_SDK_17.0.2 .
Besides, the related software and the Segger Embedded Studio are installed.
Occurred Problems :
When...
Dear members,
How can I wake up the system after idle ?
It goes to main loop, but never wakes up if there's a signal from HRM,BSC or B.Power after search time out and...
Dear everyone.
Sorry for my cheep question.
We are using nRF51822 as Bluetooth4.1 with Softdevice S120 and S110 .
Is this device affected by the "BrakTooth" attack?...
