Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Hello,
I am using the Thingy:91 PCB and I have disabled the nRF52 by cutting SB4 and soldering SB3. This makes me unable to log through UART. For this reason I implemented...
To the kind attention of Nordic support team,
I need to disable, enable gzll more times. When enabling it, code gets often stuck in my case as in figure: nrf_impala.c 442...
I have achieved Bluetooth connection between 1*ble_central<------>6*ble_peripheral.
But, ble_peripheral sometimes upload data at the same time, then sometimes lose data...
We're successfully using nrf_crypto_aead_crypt() with AES CCM, a 128-bit key, a 64-bit MAC, and the NRF_CRYPTO_ENCRYPT operator to encrypt some data and generate a MAC that...
HI, all,
I am trying to transfer my previous project from nrf51822 to nrf52840, and at very the beginning ,I can not make the UART/UARTE of nrf52840 work.
0, I have programmed...
Hi, everyone,
I am pretty new to nRF52 development. Right now, I have an issue with the SAADC trigger by RTC, which I follow this example . The issue that I have right now...
Hey all,
Here's another question. Many of the examples in the Nordic Connect SDK are rather large. Transferring them with MCUmgr at 115200 BAUD takes sometimes more than...
Hi
I am testing sending and receiving data between nRF51 dongle and peripheral by example of heart-rate-collector.
now I could find characteristics I need(write, read...
Hi all,
My application is as follows:
I have an android app which will send some data to a nRF DK. The data I want to send is in HEX characters between 0x00 to 0xFF. And...
Hello,
For nRF51822 and nRF52832, I'm using GPIOTE, PPI and timers to measure the duration that a pin, which is normally low, goes hi (typically 100-300 milliseconds). I...
The following questions are in regards to the instructions at nRF_Connect_SDK-modifying-a-sample-application .
In the Windows environment, I am transitioning from using...
Dear all,
I recently made a custom PCB using the aQFN73 package of the nRF52840 and, even though I respected the antenna constraints (but in 2 layers) I get no signal whatsoever...
Hi Devzone:
I am using P0.00 as SDA and P0.01 as SCL on nRF52833, And I got waveforms like below when I am doing I2C transactions:
the red waveform is SDA and the green...
