I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
hi,
After the TX interrupt event occurs, on_radio_disabled_tx() is executed.
There is a timeout event for receiving an ACK. I noticed that the timer timeout was set...
Hi
I'm a bit unsure as to how to interpret the documentation. It's my understanding that zephyr v2.4.99 is an unstable development release. But it seems to be the only release...
Hello,
4-byte long SPI messages, "1234", are sent to nRF 52DK. The code in DK is attached below. The XFER_DONE event is created before the message ends, which happens very...
I thought this would be rather simple as I would design a BLE peripheral in the usual way but the source of data for the peripheral comes from a sensor sending nonconnectable...
Hi,
I am exporting SAADC example to NRF52840 Dongle and I can see this structure:
/** * @brief Input selection for the analog-to-digital converter. */ typedef enum { NRF_SAADC_INPUT_DISABLED...
Hi,
I get read service content retained after reset, and it is read by the central before I get the chance to change it. Please advise how to clear it upon restart.
Thanks...
I want to create two switch EP(if it is possible I would like to it as much switches as possible).
I am using WIndows 10 with Segger and nRF COnnect SDK v1.5.0.
I tried...
Hi, We're trying to simultaneously run BLE Eddystone and connectable mode in our application. Our device is advertising it's ID but every time I try to connect via BLE from...
Hi Team,
regarding my application I need to switch the reference voltage we are taking two deferent reference voltage Ex: one for 2.25 and another 0.75 so we have requirement...
Hi,
I am working with nrf52-ble-app-uart-relay example taken from Nordic Playground github. I have SES IDE, nRF5_SDK_16.0.0 & nRF52840 DK. The central part of the relay...
Hi
Having the nRF5340DK board and following few examples from the nRD SDK Connect. After programming the application core, need to program the network core using the hci_rpmsg...
Hi, I already read more threads about this issue. How to program the nRF52840-Dongle. Most threads go to far in details, where my knowledge ends... I just want to run a simple...
I am trying to include software support for the ST LIS2DE12 accelerometer chip which is found in V1.5.0/zephyr/modules/kconfig.st as
config USE_STDC_LISDE12
bool
V1...
Hi,
I'm looking for the source code to the program that came on the Thingy91
I have not been able to find the source anywhere in the documentation
or sample code....
I am trying to port an nRF51 project that runs on the nRF51 DK using Keil to the nRF52840 DK using Segger Embedded Studio. Clearly the best way to start is to take an example...
