I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
Hi everyone,
I'm a beginner with nordic development and I managed to screw up my development kit. It started when I was trying to figure out the BLE blinky app with my IOS...
Hi,
I'm working on an IoT project with NRF52832 ( S132) . I need to connect this device to mqtt over 6LoWPAN (IPv6) and run it on a button cell battery CR2032 for as long...
HI,
I am trying to connect to our cloudmqtt account where the topics are dynamically created because of which is it not possible to pre-program a specific topic.
I would...
Hi,
it came to my attention that the inductor Murata LQP15MN3N9B02D (3.9nH) that is used in the antenna matching circuit of the nrf52832 reference design has become NRND...
Hi every one,
I'm a development product with chipset NRF52811, using soft device S112 and SDK 15.3.0.
My device will wake up and send data whenever I press the button...
Hello Nordic Team, I'm starting a project which consist in measure pressure in multiple points and send this data to central unit. At this point, using strain gauges with...
Hi,
I am using the Thingy 91 and I have a program, where I first read GPS, then switch to NBIoT Mode and then send the data to a server.
However if I switch the Antenna...
Hi, Nrf Connect was used as a central.When I send a data (Uart Service) from the app to the characteristic value of a Service (UUID:0x0002), the callback function of another...
Devices: nRF52840
Example: Light switch provisioner/client in one device
I have been looking into provisioner flash storage and am trying to understand at a fundamental...
Hi,
I flashed my 2 PCA10056 boards with light switch server and client respectively. As a provisioner, I am using my IPhone 6 wirh nRF`Mesh app.
After the provisioning...
Hi,
I am wondering how I would describe the capabilities of a device. Say, I were to develop a device that contains a light bulb and a fan. I could now use two elements...
Hi,
I am using Nrf Sdk Mesh V3.1.0 with softdeviceS132 and sdk board Nrf52832 and esp module
I want to implement Dfu process for my devices preset in mesh network and...
Hi everyone,
I am trying to include a header file into my project but the build solution fails with the error "No such file or directory"
I have placed my .c and .h file...
Hello,
From my software i get gps data and send to my webserver, periodically.
This works for some time then the system blocks! Nothing works anymore.
At first...
Dear team,
I have an understanding that BT Mesh is based on BT4.0 advertisement so even if we select a module with BLE5.0 the TX power will be less while using BT Mesh...
