How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
My environment: Keil 5; nRF52832 SDK 15.2 ; Softdevice S132 6.1.0
The uart bootloader code locate in the address: 0x70000 - 0x80000 ; (The MBR in 0x70000)
The application...
Hi,
I want to read and write MAX30100's registers. How can i do that? I tried a lot of solutions but I didn't solve that.
For example; MAX30100's address is 0x57. And...
Greetings!
I am using the SDK Mesh 3.1.0 and Softdevice 6.1.0 with the nRF52840 Dev kit: (PCA10056)
So, in my previous post ( https://devzone.nordicsemi.com/f/nordic...
I am using the nRF 15.2 SDK for Thread and Zigbee. I am currently trying to use the debugger in SES, but when I upload the code, SES complains that it can't find the source...
Hi
my devices use USB HID to PC now, and I have PC GUI.
I want use BLE send My device data to PC ( windows 10 )
if I use BLE HID services to PC
I need to do any...
Hi;
I am trying to add uart central to multilink central examble. I added some of uart part to multilink. i am trying to link two peripheral to central. when two peripheral...
Hello Nordic, for my project work i am using nrf52840 dk. with segger embeded studio i drag and drop the s140 softdevice hex file into the J-Link (chip PCA10056). and i tried...
Hello,
we are using the Nordic nRF52832, and I was hoping to update to the new SoftDevice S113 v7.0.0 as it seems like a better fit for our use cases than S132.
However...
My flash_placement.xml file is here and I am getting this error `.bootloaderSettings' will not fit in region `UNPLACED_SECTIONS'.`UNPLACED_SECTIONS' overflowed by 1024 bytes...
Hi
I have done multilink with uart and getting data from multiple ble_uart peripheral. now i have to read data from only one peripheral . what will do for that.
I am using...
Hello
I was wondering if there have been any changes in supporting IAR for nRF Mesh?
In your answer from about a year ago you wrote that you were not currently planning...
Hi,
I have some questions:
1. How does the process of getting addresses to the Nodes happen in Mesh stack? Is it automatically or I need to set it when I flashed the...
Trying to run the "Alert Notification Application" example in nRF SDK v15.3.0 on either a Windows 10 system or a Ubuntu 18.04 LTS system. Following the instructions, I can...
hi,
i want to use mesh network in my project.our requirement is multiple nodes will be sending data to one master node.is there any example code.
Regards,
jagadee...
