I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
NCS 2.7
NRF52840
I have 2 different applications: app and mfg_app
I have 2 different boards: small_flash and big_flash
I need to build all 2*2 combinations.
I...
I'm updating my development environment to new PC.
I've downloaded and installed nrfConnect.
The toolchain manager on tje new PC only references SDKs 2.7.0, 2.8.0 and...
Hi,
I have 3 NRF52840 dongles plugged in a Raspberry Pi 3B+. One of them is used to communicate with my phone with BLE, and on the two others I have loaded the NRF Sniffer...
Hi, I've noticed a strange behavior of my device. I'm using a nRF9160-based custom board with nCS v2.6.0 and modem version 1.3.6. Long story short - after trying to acquire...
1.
2.
Hello. It is under development as nrf7002.
I'd like to ask you about the quasi-board configuration I saw in the sample example.
The target board in...
Hello everyone,
I am currently using Nordic NRF5340-DK board for development and I have run the zephyr UART driver sample that works an echo bot. This sample works fine...
nRF 52832 DK advertizes successfully .
But the name of the DK is not listed in nrf connect for mobile app. Peripheral_UART is the sample code that I have compiled.
Hello,
I am currently on a project where we have 4 BLE peripheral devices equipped with NRF52840 connecting to one BLE Central, which is an app on iOS or Android. From time...
Hi,
We're planning to integrate ble_app_uart and ble_app_uart_c into our project. Before integration, we tested the ble_app_uart example code on one development board. After...
Hi all,
I'm trying to get a UART connection running at 460800 bps, and it fails about 1-5% of the time, meaning that I receive less bytes than I expect. This happens a lot...
Hi,
I want to debug [i.e. attach to and single step] mcuboot [running as second stage bootloader] using Ozone and JLink.
I can connect to the board via the debugger...
Hi! I am trying to sync the time on my nrf9160dk with date_time_now() or date_time_uptime_to_unix_time_ms() but it seems that they return a very low unix_time_ms (only 1089262423ms...
The nRF7002DK board has a Vdd of 1.8 V, unlike every other Nordic board I've seen which use 3.3V. I assume this is due to the nRF5340 errata that state that the QSPI bus ...
Hi,
We are Designing the Long range module using nRF54L15 with nRF21540 FEM.
Now want to use Dual Antenna simultaneously. we have Couple of questions
Please guide us...
